ENGINE
L4100, WSM
1-S48
(EU)
Camshaft Alignment
1. Support the camshaft with V blocks on the surface plate at both
end journals.
2. Set a dial indicator with its tip on the intermediate journal.
3. Measure the camshaft alignment.
4. If the measurement exceeds the allowable limit, replace the
camshaft.
9Y1210278ENS0097US0
Cam Height
1. Measure the height of the cam at its highest point with an
outside micrometer.
2. If the measurement is less than the allowable limit, replace the
camshaft.
9Y1210278ENS0076US0
Oil Clearance of Camshaft Journal
1. Measure the camshaft journal O.D. with an outside micrometer.
2. Measure the cylinder block bore I.D. for camshaft with a cylinder
gauge, and calculate the oil clearance.
3. If the oil clearance exceeds the allowable limit, replace the
camshaft.
9Y1210278ENS0077US0
Balancer Shaft Side Clearance
1. Set a dial indicator with tip on the balancer shaft.
2. Measure the side clearance by moving the balancer shaft to the
front and rear.
3. If the measurement exceeds the allowable limit, replace the
balancer shaft.
9Y1210278ENS0103US0
Camshaft alignment
Allowable limit
0.01 mm
0.0004 in.
Cam height of intake and
exhaust
Factory specification
33.90 mm
1.335 in.
Allowable limit
33.85 mm
1.333 in.
Oil clearance of
camshaft journal
Factory specification
0.050 to 0.091 mm
0.0020 to 0.0035 in.
Allowable limit
0.15 mm
0.0059 in.
Camshaft journal O.D.
Factory specification
39.934 to 39.950 mm
1.5722 to 1.5728 in.
Cylinder bearing I.D.
Factory specification
40.000 to 40.025 mm
1.5748 to 1.5757 in.
Balancer shaft side
clearance
Factory specification
0.07 to 0.22 mm
0.0028 to 0.0087 in.
Allowable limit
0.30 mm
0.0118 in.
KiSC issued 08, 2012 A
Summary of Contents for Kubota L4100
