TRANSMISSION
L4100, WSM
3-S37
(EU)
Clearance between Differential Pinion Shaft and Differential
Pinion
1. Measure the differential pinion shaft O.D.
2. Measure the differential pinion I.D. and calculate the clearance.
3. If the clearance exceeds the allowable limit, replace them.
9Y1210278TRS0043US0
Backlash between Differential Pinion and Differential Side
Gear
1. Set a dial indicator (lever type) on the tooth of the differential
pinion.
2. Hold the differential side gear and move the differential pinion to
measure the backlash.
3. If the measurement is not within the factory specifications,
adjust with the differential side gear washer.
(Reference)
• Thickness of differential side gear washers
1.5 mm (0.059 in.)
1.6 mm (0.063 in.)
1.7 mm (0.067 in.)
9Y1210278TRS0044US0
Clearance between
differential pinion shaft
and differential pinion
Factory specification
0.0900 to 0.132 mm
0.00354 to 0.00520 in.
Allowable limit
0.25 mm
0.0098 in.
Differential pinion shaft
O.D.
Factory specification
19.950 to 19.971 mm
0.78543 to 0.78626 in.
Differential pinion I.D.
Allowable limit
20.061 to 20.082 mm
0.78980 to 0.79063 in.
Backlash between
differential pinion and
differential side gear
Factory specification
0.15 to 0.30 mm
0.0059 to 0.011 in.
Allowable limit
0.40 mm
0.016 in.
KiSC issued 08, 2012 A
Summary of Contents for Kubota L4100
