HYDRAULIC SYSTEM
L4100, WSM
8-S23
(EU)
Clearance between Hydraulic Arm Shaft and Bushing
1. Measure the hydraulic arm shaft O.D. with an outside
micrometer.
2. Measurement the bushing I.D. with an inside micrometer, and
calculate the clearance.
3. If the clearance exceeds the allowable limit, replace the
bushing.
9Y1210278HYS0042US0
(3) Cylinder Safety Valve
Operating Pressure of Cylinder Safety Valve
1. Attach the cylinder safety valve to injection nozzle tester with a
safety valve setting adaptor.
2. Measurement the operating pressure of the cylinder safety
valve.
3. If the operating pressure is not within the factory specifications,
adjust by turning the adjusting screw (1).
4. After adjustment, tighten the lock nut (2) firmly.
NOTE
• Use specified transmission fluid (see page G-9.) to test the
operating pressure of the cylinder safety valve.
9Y1210278HYS0033US0
Clearance between
hydraulic arm shaft
and bushing
Factory
specifica-
tion
Right
0.125 to 0.230 mm
0.00493 to 0.00905 in.
Left
0.125 to 0.220 mm
0.00493 to 0.00866 in.
Allowable
limit
Right
0.50 mm
0.020 in.
Left
0.50 mm
0.020 in.
Hydraulic arm shaft
O.D.
Factory
specifica-
tion
Right
44.920 to 44.950 mm
1.7685 to 1.7696 in.
Left
39.920 to 39.950 mm
1.5717 to 1.5728 in.
Bushing I.D.
(after press fitted)
Factory
specifica-
tion
Right
45.075 to 45.140 mm
1.7746 to 1.7772 in.
Left
40.075 to 40.140 mm
1.5778 to 1.5803 in.
Cylinder safety valve
operating pressure
Factory specification
19.7 to 22.5 MPa
200 to 230 kgf/cm
2
2850 to 3270 psi
Tightening torque
Lock nut
59 to 78 N·m
6.0 to 8.0 kgf·m
44 to 57 lbf·ft
(1) Adjusting Screw
(2) Lock Nut
(3) Spring
(4) Seat
(5) Ball
(6) Housing
KiSC issued 08, 2012 A
Summary of Contents for Kubota L4100
