background image

1. Each installation site must be evaluated and the proper securing method determined by the

installer. Some soils require staking or securing different from that which was provided with the
tent.

2. Good judgment and common sense must be used along with installation guidelines. It is the

responsibility of the tent installer/maintainer to anticipate the severity of the weather along with
the proper time and method of setup and take down. Evacuation of the tent is recommended
before weather becomes extreme. A successful event is a safe event.

3. Proper safety equipment, such as hard hats, steel toe shoes, and safety glasses, should be used

to ensure a safe setup and take down.

ASSEMBLY INSTRUCTIONS

MODEL

MQ1020

PEAK MARQUEE TENT

CAUTION

IMPORTANT:

PLEASE READ INSTRUCTIONS PRIOR TO ERECTING THE TENT.

PROPER INSTALLATION WILL ENSURE MAXIMUM USAGE AND

STABILITY OF THIS STRUCTURE.

IF FURTHER INFORMATION OR CLARIFICATION OF ANY PART OF

THE ENCLOSED INSTRUCTION IS REQUIRED, PLEASE CONTACT:

WARNER SHELTER SYSTEMS LIMITED

1-800-661-6155 OR E-MAIL: warner@wssl.com

..\graphicshome\Marquee\Manuals\MQ1020\MQ1020 Manual 2007.FH11

Summary of Contents for MQ1020













Reviews: