background image

D. Customer Service

Customer Service hours are 8:00 AM to 5:00 PM, Pacific Time, Monday through Friday.  When 
calling, please be prepared to give the name and make of the unit, its serial number, and a
description of its symptoms.  If the unit should need to be returned for factory repair it must be 
accompanied by a Return Authorization number from Customer Service.

WTI Customer Service

5 Sterling

Irvine, California   92618

949-586-9950

Toll Free:  1-800-854-7226

Fax:  949-457-8138 

e-mail:  service@wti.com

Trademark and Copyright Information

WTI and Western Telematic are trademarks of Western Telematic Incorporated.  All other
product names mentioned in this publication are trademarks or registered trademarks of their
respective companies.

Information and descriptions contained herein are the property of Western Telematic, Inc..
Such information and descriptions may not be copied, disseminated or distributed without the
express written consent of Western Telematic, Inc..

© Copyright Western Telematic Inc., 1997, 2000
All rights reserved.

June 2000
September 1997
Part Number: 12365   Revision: C

Apx-4

CAS-81 Code Activated Switch

Appendices

Summary of Contents for CAS-81















Reviews: