background image

Operation

pHotoFlex

®

pH

16

ba75977e03

10/2017

Maintenance, cleaning

Maintenance

The meter is almost maintenance-free.
The only maintenance task is replacing the batteries or rechargeable 
battery.

NOTE

Make sure the poles of the batteries are the right way round. The ± 
signs on the batteries must correspond to the ± signs in the battery 
compartment.

Dispose of used batteries according to the local regulations of your 
country. 

End users within the European Union are obligated to return used bat-
teries (even ecologically compatible ones) to a collection point set up 
for recycling purposes. 

Batteries are marked with the crossed-out waste container symbol. 
Therefore, they may not be disposed with the domestic waste.

Cleaning

Occasionally wipe the outside of the meter with a damp, lint-free cloth. 
Disinfect the housing with isopropanol as required.

NOTE

The housing components are made out of synthetic materials 

1

Open the battery compartment:
– Unscrew the two screws (1) on the underside of the meter,

– Remove the lid of the battery compartment (2).

2

If necessary, take four old batteries out of the battery 
compartment.

3

Insert four batteries (3) in the battery compartment.

4

Close the battery compartment and fix it with the screws.

1

2

Summary of Contents for pHotoFlex pH



























Reviews: