background image

FLEXCOMM 

II

 

 

C-5000 (Non-Digital) 

Installation Manual 

 

150-1355-000 Rev. M 

CONFIDENTIAL AND PROPRIETARY TO COBHAM 

Page 137 

 

D.  Checkout Procedure (Continued) 
 

3.A.(2) (Continued) 

3000 Hz +/ 500 Hz, adjust audio panel for more/less output. Also verify transmit frequency is 

correct. 

(3)  Remove the audio source and transmit on a selected frequency; verify that sidetone audio 

is heard in the headset. 

(4)  Connect the through line Watt meter between the radio and antenna and check forward 

and reflected power at each of the frequencies listed in the tables below that is 

appropriate for the type of transceiver being tested. The Reflected power should be less 

than 30% of the forward power. 

(5)  Perform Tests 1 - 4 on transceiver #2. Use the secondary mic/headset port for audio 

input/output. 

B.  Receiver Verification 

(1)  Use the communication analyzer to measure receiver sensitivity at the frequencies listed 

in tables 6-7 thru 6-12 (Select the table based on appropriate transceiver model). 

Remember that frequencies below 400 MHz use the RT-5000 "N" RF connector and 

frequencies above 400 MHz use the "TNC" RF connector. Use the manual channel on the 

C-5000 to tune the transceiver. Verify RT #1 by varying the input signal until 12 dB sinad 

is measured. The signal level should be < .6

V for all FM Channels. THE INSTALLER 

MAY BE REQUIRED TO PRESS THE "TEST" BUTTON TO GET AUDIO OUT OF THE 

RADIO

(2)  Perform the same tests on transceiver #2 if available. 
(3)  With the Antennas connected to their corresponding radios, transmit with the 

Communications analyzer to all receivers in each radio using an antenna that is located 

10-20 feet away from each C-5000 system antenna. Verify that the signal is received with 

good audio quality and the squelch light operates properly for each receiver. 

C.  Encryption Verification 

If an external encryption system is being used, select a channel that accesses the encryption unit, 

and test RX/TX encryption capability. Remember to load encryption keys into the unit first. Use a 

handheld or communication analyzer equipped with your encryption type to communicate with the C-

5000 transceivers under test

Summary of Contents for FLEXCOMM II C-5000
























































































































































Reviews: