8
Intended Use
The unit is intended to bond wood, plastic, metal,
ceramic and other materials.
For damage caused by usage other than intended, the
user is responsible.
Product Features
1
Nozzle
2
Glue stick
3
Stroke-range adjustment
4
Handle
5
On/Off switch
6
Feed regulation button
7
Stand
8
Temperature controller
9
Screwdriver
Not all of the accessories illustrated or described
are included as standard delivery.
Tool Specifications
Operation
Initial Operation
Thoroughly clean the surfaces to be bonded first.
Insert the adhesive stick
2
into the opening to the stop.
Insert the mains plug of the unit into an earth-conected
outlet.
Switch the glue gun on with On/Off switch
5
.
Place the glue gun with its stand
7
on a firm surface,
which is resistant against possibly dripping hot adhe-
sive.
Allow the glue gun to heat up for approx. 6–8 min-
utes.
Use only Würth adhesive sticks with a diam-
eter of 12 mm.
Adjust the desired operating temperature with temper-
ature controller
8
.
Apply the glue gun via the nozzle
1
to the bonding
location. Depending on the amount of pressure
applied to the feed regulation button
6
, the required
amount of adhesive can be adapted to the bonding
location.
Firmly press the workpieces to be bonded together; the
cooling or curing time depends on the type of adhesive
sticks used, respectively on the type of material.
Do not under any circumstances pull an
unused adhesive stick out of the glue gun.
To replace the adhesive stick being used, cut off the
projecting end of the adhesive stick
2
and insert a new
adhesive stick
2
. Actuate the feed regulation button
6
several times to clean the heating compartment from
the old adhesive.
After finishing work, place the glue gun with the stand
7
onto a firm surface.
Danger of burning!
Do not lay the glue gun aside
as long as it is still in operation. This can lead to uncon-
trolled leakage of adhesive.
Note:
Do not place a hot glue gun into the tool case,
as this can lead to uncontrolled leakage of adhesive.
For longer work breaks and after finishing work, pull
the mains plug.
Adjusting the Operating Tempera-
ture
The operating temperature depends on the type of
adhesive being used.
Set the temperature at the temperature controller
8
to
the desired value using the screwdriver
9
.
In delivery condition, the glue gun is set to a tempera-
ture of 180–190°C.
Setting the Stroke Limitation
Loosen the lock nut.
Set adjustment screw
3
in such a manner that the feed
regulation button
6
is at the desired starting position
and the desired amount of adhesive is applied for each
working stroke.
Tighten the lock nut to lock the setting.
Glue gun
HKP 220
Article number
0702 623 X
Rated power
220 W
Operating temperature
140 –220 °C
Melting capacity
1)
0.7 –1.2 kg/h
Adhesive
∅
12 mm, Würth hot
melt adhesive sticks
Weight
0.6 kg
Class of protection
I
Degree of protection
IP 20
1)
Depending on the type of adhesive stick used
OBJ_BUCH-0000000038-003.book Page 8 Tuesday, February 9, 2016 3:04 PM
Summary of Contents for 07026231
Page 3: ...3 OBJ_BUCH 0000000038 003 book Page 3 Tuesday February 9 2016 3 04 PM...
Page 42: ...42 W rth OBJ_BUCH 0000000038 003 book Page 42 Tuesday February 9 2016 3 04 PM...
Page 71: ...71 W rth OBJ_BUCH 0000000038 003 book Page 71 Tuesday February 9 2016 3 04 PM...
Page 84: ...84 Bosch W rth OBJ_BUCH 0000000038 003 book Page 84 Tuesday February 9 2016 3 04 PM...
