18
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 77 dB(A); sound power level 88 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745:
Cutting board: a
h
=5.5 m/s
2
, K=1.5 m/s
2
,
Cutting sheet metal: a
h
=5.0 m/s
2
, K=1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under “Tool Specifications” is in conformity with all
relevant provisions of the directives 2009/125/EC (Regula-
tion 1194/2012), 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
Adolf Würth GmbH & Co. KG, Abt. PCM,
Reinhold-Würth-Straße 12–17
74653 Künzelsau, Germany
Künzelsau: 31.08.2014
Battery Charging
Use only the chargers listed in the tool specifi-
cations.
Only these chargers are matched to the lithium-
ion battery of your power tool.
Note:
The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
Observe the notes for disposal.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
5
show the charging status of the battery
1
. The battery charge-
control indicator only illuminates for 5 seconds after start-up.
When no LED lights up after switching on, then the battery is
defective and must be replaced.
Removing the battery (see figure A)
To remove the battery
1
press the unlocking buttons
2
and
pull out the battery downwards.
Do not exert any force.
Weight according to
EPTA-Procedure 01/2003
kg
1.5
1)
Permitted ambient temperature
– during charging
– during operation
2)
and during storage
°C
°C
0...+45
–20...+50
Recommended batteries
0700 996 2XX
Recommended chargers
0700 896 XXX
Cordless Jigsaw
STP 10-A
1) depending on the battery pack being used
2) Limited performance at temperatures <0 °C
Marcel Strobel
General Manager
Dr.-Ing. Siegfried Beichter
General Manager
LED
Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
Flashing light 3 x green
Empty
OBJ_BUCH-2273-001.book Page 18 Friday, October 24, 2014 9:36 AM
