11
We reserve the right to make changes without notice
Noise/vibration
The measured values conform to EN 50 144.
The A-rated noise level of the gun is typically below 70
dB(A). During operation, the noise level might exceed
85 dB(A).
Wear hearing protection!
The hand-arm vibration is typically lower than 2,5 m/s
2
Environmental protection
Reuse and recycling instead of
waste disposal.
Dispose of the rivet gun, its accessori-
es and the packaging material in an
environmentally friendly manner for
recycling, where this is possible. Bring
guns to be disposed of to the local recycling collection
centre or return them to WÜRTH.
Warranty
This WÜRTH rivet gun is covered by warranty accor-
ding to the applicable national regulations. The war-
ranty period begins on the date of purchase (please
retain invoice or delivery note as proof of purchase).
Faults covered by warranty are eliminated by replace-
ment or repair. Damage caused by improper operation
of the gun is not covered by warranty.
Claims under warranty shall only be considered, if the
rivet gun is returned fully assembled to a WÜRTH agen-
cy, your WÜRTH sales representative or a customer ser-
vice workshop for air-powered equipment authorised
by WÜRTH.
Declaration of Conformity
We herewith declare that this product conforms to the
following standards and directives: In accordance with
Directive 98/37/EG.
07
Adolf Würth GmbH & Co. KG
Troubleshooting
Fault/malfunction
Possible cause
Remedy
Gripper jaws fail to hold a
rivet
Gripping jaws dirty
Clean gripping jaws
Gripping jaws worn
Replace gripping jaws
Insufficient gun stroke length
Add hydraulic oil
Insufficient operating pressure
see rated operating pressure (machine data)
Rivet pin is not removed
by vacuum to the waste
collector
Waste collector full
Empty waste collector
Incorrect tip used
Change tip
Tip worn
Replace tip
Rivet pin jammed in gripper jaws
Disconnect the gun from the compressed
air supply line.
Dismantle the tensioning sleeve and
remove the rivet pin.
Clean the gripping jaws and the tension-
ing sleeve and oil the sliding surfaces; if
the parts are worn, replace them.
Summary of Contents for PNG 102
