background image

2

Technical Support: support@wyrestorm.com US: +1 866 677 0053 EU: +44 (0) 1793 230 343

Contents

1.     Introduction

CONTENTS AND INTRODUCTION

Wyrestorm HDBaseT™ extender sets comprise of 

a transmitter and receiver to lengthen distribution 

of uncompressed 1080p HD video @60Hz and 

HD multi-channel audio, high speed internet and 

control up to 100m (328ft) via single category 

cable, regardless of HDCP source encryption.

The EX-1UTP-100-POH and EX-1UTP-IR-100-EDID 

extenders retain the rock-solid reliability of HDBaseT™ 

transmission technology with bidirectional control of 

source and display from either location via IR and 

RS232.  Both models contain EDID management to 

manually handle device communication issues during 

installation and include the added advantage of 1:2 

splitting capabilities to duplicate the receiver HDMI 

output, allowing connection to an additional display or 

projector.   

Ethernet pass-through allow both models to be fully 

cascaded up to 7 times to further expand distribution, 

while the EX-1UTP-100-POH also features Power-

over-HDBaseT to enable true 5-play convergence 

for distribution of video, audio, control, Ethernet and 

Power through a single Cat5e/6 cable.

Wyrestorm HDBaseT™ extenders offer incredible 

flexibility and stability of signal distribution combined 

with innovative features and an ease of use that 

provides solutions where stable HD transmission 

and control over distance  is required, whilst also 

eliminating the need for additional control and video 

cables on installation, whether in a residential or 

commercial setting.

For further information on this product and other 

Wyrestorm ranges, visit our website or download our 

latest product guide. 

www.wyrestorm.com

Introduction

Features

Safety Precautions

Packaging Contents

Connection & Operation

Typical Applications

Updating RS232 Settings on the 
EX-1UTP-IR-100-POH Receiver

EDID & Upgrade Switcher Instruction

Specification

i. EX-1UTP-IR-100-EDID
ii.EX-1UTP-IR-100-POH

Maintenance

Product Service

Panel Descriptions
i. 

 EX-1UTP-IR-100-POH Transmitter

ii. 

EX-1UTP-IR-100-POH 

Receiver

iii. 

EX-1UTP-IR-100-EDID Transmitter

iv. EX-1UTP-IR-100-EDID Receiver

1

2

3

4

5

6

7

8

9

10

11

12

13

Mail In Service

Warranty

Warranty Limits and Exclusions

Installation Test Notes

14

15

16

Part Number

     EX-1UTP-IR-100-EDID 

Part Number

     EX-1UTP-IR-100-POH

Summary of Contents for EX-1UTP-IR-100-EDID













Reviews: