Wiring and Connections
HDBaseT Wiring
Wiring for HDBaseT follows the EIA T568B standard.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference can have an adverse effect on
HDBaseT transmission limiting performance. Steps should be taken to minimize these factors (or remove completely) during installation for best
results.
Specifications
Pin 1 Pin 8
RJ-45 Connector (Gold Pins Facing Up)
Pin 2: Orange
Green
Pin 6:
Pin 1: White/Orange
Pin 5: White/Blue
Pin 3: White/Green
Pin 7: White/Brown
Pin 4: Blue
Pin 8: Brown
Pin 2: RX (Receive)
Pin 1: TX (Transmit)
Pin 3: Ground (GND)
Wire colors shown follow EIA-561 standard.
1 2 3
RS232 Wiring
Audio and Video
Audio Connection
3-pin phoenix port (MIC), 3-pin phoenix
port (Stereo)
Audio Formats
Stereo
Video Connection
HDMI 1.3a (input/output), HDBaseT
(output)
Video Resolution
HDMI: Up to 1920x1200p @ 60Hz
VGA: Up to 1920x1200 @ 60Hz
Color Depth
36bit
Control
Method
Bi-directional IR, bi-directional RS-232,
front panel buttons, I/O control devices,
LAN (Telnet & Web GUI)
Ports
IR, RS232-1, RS232-2, CONTACT IN,
LED OUT, LAN
Power
Input Power
100-240VAC 50/60Hz
Max Power Consumption
26.5W
HDBaseT (PoH)
15.4W (HDBT OUT)
Phantom Power (for MIC)
48 VDC 100 mA
Dimensions and Weight
Height
50mm/1.9”
Width
440mm/17.3”
Depth
280mm/11.0”
Weight
4.0kg/8.81lbs
Environmental
Operating Temperature
32°F ~ 113°F (0°C ~ 45°C) 10% ~ 90%,
non-condensing
Storage Temperature
-4°F ~ 140°F (-20°C ~ 70°C) 10% ~
90%, non-condensing
ESD Protection
±8kV (Air-gap discharge), ±4kV (Contact
discharge)
Surge Protection
Voltage: ±1 kV
REGULATORY
Safety and Emission
CE | FCC
RoHS
Compliant
Cable
Performance Guide
SW-1001-HDBT
0ft
328ft
32ft
65ft
98ft 131ft 164ft 197ft 230ft 262ft 295ft
0m
100m
10m
20m 30m
40m 50m
60m 70m
80m 90m
HDMI*
Transmission
HDBaseT Class B Cat5e/6
Transmission
HDBaseT Class A Cat5e/6
Transmission
Operation
The SW-1001-HDBT features hot-plug detection to enable instant
switching to any source device plugged in to the rear of the unit or a
desk plate, and instant disconnection from any device unplugged. On
removing a connected device, the SW-1001-HDBT will return to the
last available active source connected.
The unit also includes CEC support to trigger an ‘ON’ command for
the sync device when connecting an active source. Disconnecting
or powering off sources instructs the sync device to turn off after a
predefined period of time – duration variable between 1min-1hour or
function can be deactivated.
(See full manual for further CEC details and customization.)
Control the SW-1001-HDBT via local push button, Web UI or RS232
using control protocols, with local source selection made by pressing
the relevant button on the front panel.
A static green LED above the input button indicates the source
selected and flashing blue STATUS LED illustrates the SW-1001-
HDBT is active and functioning correctly.
See full manual for operation using Web UI and RS232.
