background image

 

35  

 
After completing the password changing, system will record 
the 4 digits password and when you reboot the machine or 
need to change the password again, system will ask you to 
input the current password for identification. 
 
Password can be changed again by setting Yes to the 
Change Password function but the current password must 
be input correctly first. If user wants to disable the password 
function, simply set the password to 0000 and then the 
password function will be deactivated (0000 cannot be set 
as password).   
 
Wrong password input during the booting stage will cause 
the hang of duplicator and freeze all operation. User must 
restart the machine to input the correct password again. 
 

6.1.20 Startup Command 

 
This setting specifies the first function appeared when 
duplicator is turned on so as to avoid repeated selection all 
the time. 
 
Press MODE switch to change and GO to exit. 
 

6.1.21  CD to CD (if HDD installed) 

 
This setting controls the source location of master data. 
Select “Yes” to bypass the existing hard drive and you can 
copy directly from CD/DVD to CD/DVD or select “No” to 
copy CD/DVD from data stored in current partition of hard 
drive. This option setting will not be saved and will be 
restored to “NO” during rebooting of duplicator. You will 
have to change the setting again after rebooting if you wish 

Summary of Contents for CD-398



























































Reviews: