manualshive.com logo in svg

X-Rite EasyTrax, Setup And Operation

X-Rite EasyTrax is a comprehensive, user-friendly solution for color management. With its straightforward setup and operation, users can achieve accurate color measurements effortlessly. Enhance your printing experience with our free EasyTrax manual, available for download on 88.208.23.73:8080, providing step-by-step instructions for optimal performance and results.

Share
Download
background image

EasyTrax Setup and Operation 

5 

Table of Contents 

Overview and Setup ............................................................................................................................. 6

 

About this manual ..................................................................................................................................... 6 

Unpacking and Inspection ......................................................................................................................... 7 

System Connections .................................................................................................................................. 7 

X-Rite Scanning Solution Software ............................................................................................................ 8 

System Requirements ........................................................................................................................... 8 

Installing the Software .......................................................................................................................... 8 

Instrument Indicator LED .......................................................................................................................... 9 

Read Head Reticule Positioning ................................................................................................................ 9 

Initial Setup ............................................................................................................................................. 10 

Manual Color Bar Alignment .............................................................................................................. 10 

Laser Alignment .................................................................................................................................. 12 

Operation .......................................................................................................................................... 15

 

Measuring a Color Bar ............................................................................................................................. 15 

Measuring a Spot Color ........................................................................................................................... 15 

Calibration ......................................................................................................................................... 16

 

Cleaning the Instrument .................................................................................................................... 17

 

General Cleaning ..................................................................................................................................... 17 

Lens Cleaning .......................................................................................................................................... 17 

Cleaning the Calibration Plaque .............................................................................................................. 18 

Cleaning the Rollers ................................................................................................................................ 19 

Appendices ........................................................................................................................................ 20

 

Service Information ................................................................................................................................. 20 

Troubleshooting ...................................................................................................................................... 20 

Calibration Plaque Replacement ............................................................................................................. 21 

Read Head Replacement ......................................................................................................................... 21 

Technical Specifications .......................................................................................................................... 22 

System Repacking Instructions ............................................................................................................... 23 

 
 

Summary of Contents for EasyTrax





























Reviews:

No comments

Related manuals for EasyTrax

Protec FI-75 MAMMO Operation Manual preview
FI-75 MAMMO
Brand: Protec Pages: 37
Pandigital PANSCN10 User Manual preview
PANSCN10
Brand: Pandigital Pages: 44
Bell and Howell Truper 3600 Operator'S Manual preview
Truper 3600
Brand: Bell and Howell Pages: 142
Plustek OpticBook 4800 User Manual preview
OpticBook 4800
Brand: Plustek Pages: 28
CUMMINS ALLISON Universal JetScan 4161 User Manual preview
Universal JetScan 4161
Brand: CUMMINS ALLISON Pages: 22
Plustek SmartOffice PS30D Quick Start Manual preview
SmartOffice PS30D
Brand: Plustek Pages: 2
Nikon AT-10 User Manual preview
AT-10
Brand: Nikon Pages: 28
Oce im2020 User Manual preview
im2020
Brand: Oce Pages: 44
UMAX Technologies Astra 1600U Operation Manual preview
Astra 1600U
Brand: UMAX Technologies Pages: 21
UMAX Technologies Astra 2100U Owner'S Manual preview
Astra 2100U
Brand: UMAX Technologies Pages: 106
Rangevision NEO Setup And Calibration preview
NEO
Brand: Rangevision Pages: 15
Adesso EZScan 2000 Specifications preview
EZScan 2000
Brand: Adesso Pages: 1
Datalogic PreScan Advanced Configuration Manual preview
PreScan
Brand: Datalogic Pages: 84
Datalogic TC1100 Reference Manual preview
TC1100
Brand: Datalogic Pages: 131
Datalogic Laser Sentinel Instruction Manual preview
Laser Sentinel
Brand: Datalogic Pages: 152
Datalogic Magellan 3450VSi Product Reference Manual preview
Magellan 3450VSi
Brand: Datalogic Pages: 352
Canon P-208 Manual preview
P-208
Brand: Canon Pages: 2
SICK ZS3608 Quick Start preview
ZS3608
Brand: SICK Pages: 2

Brands by name

Popular brands

Load more brands