X-Tronic 4020-PRO-X Instructions Manual Download

Page: 13 / 16

- 11 -

TROUBLESHOOTING

ISSUE

POSSIBLE SOLUTIONS

Unit does not

have power

• Ensure that the outlet is functional.
• Contact X-Tronic International for technical

assistance - Contact information on back of manual

Soldering Iron

“Rattles”

• This is expected behavior. The “rattle” is a small ball

that allows the unit to determine when the soldering

iron is not in use and it should go into Sleep Mode

S-E Error

• The heating element may need to be replaced
• Contact X-Tronic International for technical

assistance - Contact information on back of manual

HEA Error:

Issue with the

heater

• The heating element may need to be replaced
• Contact X-Tronic International for technical

assistance - Contact information on back of manual

TMP Error:

Issue with the

sensor

• Contact X-Tronic International for technical

assistance - Contact information on back of manual

FAN Error:

Issue with the

fan

• Contact X-Tronic International for technical

assistance - Contact information on back of manual

Summary of Contents for 4020-PRO-X

















Search results

Summary of Contents for 4020-PRO-X

Reviews:

Related manuals for 4020-PRO-X

Brands by name

Popular brands

X-Tronic 4020-PRO-X, Instructions Manual

Search results

Summary of Contents for 4020-PRO-X

Reviews:

Related manuals for 4020-PRO-X

Brands by name

Popular brands