■
Assemblage orders and methods can vary from person to person. The color and parts of products may probably
be altered in order to provide better products.
■
End treating to prevent hurting hands has been made on sections of chassis in computer case. However, please be
careful about untreated parts. Please wear gloves or other supplies to protect your hands when you take an
assemblage.
Main Board Installation Position
Special Screw For Assemblage
Special screw forHDD
Special screw forM/B,SSD,CD-ROM
Special screw forpower supply,graphic card
Installable Main Board
M/B hexagon
M/B hexagon
M/B hexagon
Supportscrewsupportscrewsupportscrew
installationhole
M/B hexagon
M/B hexagon
M/B hexagon
Supportscrewsupportscrewsupportscrew
installationhole
M/B hexagon
M/B hexagon
M/B hexagon
Supportscrewsupportscrewsupportscrew
installationhole
※
USB3.0on boardcable
connection method
Connect directly USB3.0on board cable
in inner port of main board to on board
header port.
NOTICE
！
Simultaneous connection to USB2.0
cable separated from USB3.0on board
cable is not allowed.
Main Board
Assemblage
Method
Power Supply
Assemblage Method
Special screw for M/B
Main board
M/B hexagon
Support screw
Install main board I/O shield at the back of case.
After aligning holes of hexagon support screw and main board
screw of case, use special screws for main board to assemble.
6main board support screws are basically
installed at the case. Based on main board
specification, it is able to chooseneeded support
screws to use in combination.
Specialbracket for power
supply assemblage
Back
Assemblage position of power supply
is at opposite side of chassis
Specialbracket assemblage
for power assemblage
①
Confirm special screw for power supply. (hexagon screw)
②
Confirm installation position of power supply at back on right side of case.
③
Dismantle special bracket for power assemblage of basic setting.
④
Put power supply’s fan adown.Then, push it to assemble.
⑤
Reinstall dismantled special bracket for power assemblage.
⑥
All installed power supply need special screws for power supply to assemble.
Power supply
assemblage
HDD &SSD Multi Guide Assemblage Method
SSDAssemblage Method
Graphic CardAssemblage Method
Installation Position Of Upper Cooling Fan&Water-Cooling Cooler
①
Confirm HDD bay at the right side of chassis firstly. Then, dismantle
HDD assemblage guide on HDD bay which is basically set.
②
After catching two sides of HDD assemblage guide and opening,
align HDD fixed frame with HDD. Then, installation can be started.
③
After guide whose HDD is assembled is connected to bay, then, push
it forward. And installation can be started.
④
There are screw holes that can assemble SSD at the center of multi
guide. The special screw holes can be used to assemble SSD.
①
Confirm special screw for SSD
②
Confirm place of SSD screw hole of SSDinstallation spaceat right
side.
③
After aligning SSD with SSD screw hole, use special screws of SSD
for right installation.
①
Confirm special screws for graphic card
②
After confirming installation place of graphic card, remove PCI slot
guide.
③
Align graphic card with PCI slot for right installation.
④
Installed graphic card requires matched special screws to be
assembled on PCI slot.
240mm (120mm dual) all-in-one water-cooling cooler
can be installed.
2 120mm fans at most can be installed at upper end.
240mm(120mm dual) all-in-one
water-cooling cooler can be installed
PCI slot
Graphic card
Front
Connector’s connection
direction
Connector’s connection
direction
HDD fixed frame
HDDfixedframe
screwhole for SSD
assemblage
screwhole for
SSD assemblage
screwhole for SSD assemblage
HDD fixed
frame
Connector’s
connection direction
X2PRODUCTS.COM
X2PRODUCTS.COM
