background image

www.xa.com/en

18

Precautions for Battery Use

•  NEVER insert/remove the battery when it is ON, or it may cause damage to the interface.
•    It is a MUST to check and update to the latest battery firmware and software version preceding 

operation. Loss caused by failing to do so shall be borne by the user.

•       An optimal ambient temperature range for the battery is from 10 ℃ to 45 ℃ . Chances are that fire, 

even explosions will happen at a temperature over 45℃ .

•    NEVER connect the cathode and anode with a wire or other metals, as this will cause a short circuit.
•    For heat dissipation, the battery should be immersed into pure water instead of corrosive liquids 

within the maximum and minimum level indicated for NO more than 60min, or else the battery will 
get damaged for having water leak inside.

•   Please always keep the interface clean and clean the liquid or foreign matters off it promptly. 

Otherwise, it will cause poor contact, contributing to energy loss or failure to charge.

•     Please handle the battery with care and do NOT take it apart, pierce the housing or apply pressure 

to it, including but not limited to behaviours such as sitting/standing on the battery, stacking heavy 
items on it and the like.

•    Please regularly check the components like the battery interface and the plug before use. NEVER 

clean the charging device with alcohol or other combustible liquids. NEVER use the damaged 
charging device.

•     Please place the battery and charging device on even ground with no combustible materials around 

while charging. NEVER leave the battery unattended while charging in case of an accident.

•    For your safety, keep a minimum of 30cm distance between the battery and the charger, and between 

two batteries, lest too much heat lead to the charger or battery failure, even causing dreadful 
consequences like a fire.

•   Please make sure the battery is fully charged prior to each operation. NEVER operate at full capacity 

preceding completion of charging.  

•     NEVER use batteries provided by manufacturers other than XAG, or to dismantle/replace the battery 

without permission. If necessary, please contact XAG or the authorized dealer. For the battery 
incidents, technical faults or other accidents caused by using a battery or accessories provided by 
non-XAG manufacturers, the user shall be held responsible for all the consequences arising therefrom. 

•    If one green light flashes at the end of the operation, please charge the battery to 40%~60% before 

storage. Failing to do so may damage the battery or impact battery life. Fully discharge and recharge 
the battery every 90 days to maintain battery health.

•    The battery should be stored at 10~30℃ in a dry place instead of a wet or moist environment.
•    Avoid moisture while charging the battery. Warranty does NOT cover any damage caused by problems 

not attributable to the product quality like damaged battery housing.

•     The battery is waterproof and splashproof under controlled experiment. However, rather than being 

permanent effective, the protection may get weaker due to wear and tear.

•     Please STOP using the batter swollen, leaking, deformed or with appearance damage instantly and 

contact XAG or the dealer without hesitation.

•     The liquid inside the battery is highly corrosive. In case of contact with skin or eyes, flush with fresh 

water and seek medical attention instantly.

•    To protect our environment, please properly dispose of the battery as required by the local laws and 

regulations.

Summary of Contents for 3WWDZ-20BH

































Reviews: