13. Repeat Steps 3 through 12 for Sources 2 through 4.
14. BXAUDIO4X4 Controller will need to be power cycled for commands to take effect.
PROGRAMMING KEYPAD BUTTON WITH A SEQUENCE OF COMMANDS
All programmable buttons on the BXAUDIO4X4 Keypad can be programmed to send IR sequences of up to 5 commands.
1. Program a single IR command on a keypad button following steps 1 through 7 as outlined in the section above.
2. Press the SEQUENCE
[7]
button located on the front of the BXAUDIO4X4.
a. Confirm the STATUS LED
[14]
is illuminated GREEN
3. Aim the Manufactures Source Remote at the IR Learning eye on the front of the BXAUDIO4X4
[5]
.
4. Press and Release the corresponding button on the devices remote.
5. If the code was learned correctly the STATUS LED will turn OFF and the PROGRAM KEYPAD LED will remain
GREEN
6. Repeat steps 1 thru 5 for up to a total of 5 commands. To program a DELAY between commands, proceed to the
next section before repeating.
PROGRAMMING TIMED DELAYS
Timed delays can be placed in-between commands in a sequence in 1 Second intervals for up to a total of 7 Seconds.
After a successful IR Command has been learned;
1. Make sure the PROGRAM KEYPAD LED is GREEN and the STATUS LED is OFF.
2. Press the DELAY
[8]
Button on the front of the BXAUDIO4X4 to enter a 1 Second Delay.
3. The STATUS LED
[14]
will blink GREEN
4. To add more Delay time, repeat steps 1-3 for a maximum of 7 seconds of delay.
Note:
If more than 7 DELAY’s are entered, the count will reset to 1 SECOND on the eighth delay.
PROGRAMMING TOGGLE IR COMMANDS
Some devices use TOGGLE IR codes where the devices remote actually has two IR codes associated to the same
button. This is sometimes common with POWER commands. If it is not known if a Toggle command is present, start by
learning the code as a single command. If the function is not working correctly or only works on every other press of the
button, then try the following:
1. Enable PROGRAM MODE
[10]
(Make sure an LCKP4 Keypad is plugged into the Zone 1 Keypad port and the
Keypad is ON.
2. Press the proper SOURCE BUTTON
[35, 36, 37, or 38]
on the LC4KP Keypad for the device to be programmed.
3. Press the PROGRAM KEYPAD
[2]
button on the front of the BXAUDIO4X4.
a. Confirm the PROGRAM KEYPAD LED
[11]
is illuminated GREEN.
4. Press the button on the LC4KP KEYPAD to be programmed
a. Confirm the STATUS LED
[14]
is illuminated GREEN
5. Aim the Manufactures Source Remote at the IR Learning eye on the front of the BXAUDIO4X4
[5]
.
6. Press and Release the corresponding button on the devices remote to record the
first
toggle command (make
sure to use a short, quick press of the devices remote when learning commands).
Note:
If the first toggle command was learned correctly the STATUS LED will turn OFF and the PROGRAM
KEYPAD LED will remain GREEN.
7. Press the TOGGLE button
[6]
on the front of the BXAUDIO4X4.
a. The PROGRAM KEYPAD LED
[11]
should turn ORANGE.
b. The STATUS LED
[14]
should turn GREEN
8. Aim the Manufactures Source Remote at the IR Learning eye on the front of the BXAUDIO4X4 and press and
release the corresponding button on the devices remote to record the
second
toggle command.
9. If the STATUS LED turned OFF the TOGGLE Command has been learned correctly.
DELETING A MACRO
To delete a Macro programmed under a single Keypad button:
1. Enable PROGRAM MODE (Make sure an LCKP4 Keypad is plugged into the Zone 1 Keypad port and the Keypad
is ON.
2. Press the proper SOURCE BUTTON on the LC4KP Keypad for the device to be programmed.
3. Press the PROGRAM KEYPAD button on the front of the BXAUDIO4X4.
a. Confirm the PROGRAM KEYPAD LED is illuminated GREEN.
4. Press the DEL button on the front of the BXAUDIO4X4.
a. Confirm the PROGRAM KEYPAD LED is now illuminated RED.
5. Press the BUTTON on the LC4KP KEYPAD to be deleted.
The PROGRAM KEYPAD LED will turn OFF when the macro is deleted
08901691 Rev.A 07/26/05
