Model MRC88m / MRAUDIO8x8m
Page: 73
© 2009 Xantech Corporation
Source 1 will automatically be selected and by adding a “PLAY” command for a CD player to the
sequence, Zone 1 will always default to CD when turned ON. Pressing the “POWER” button again
will turn the zone “OFF”. (Be sure to set the PLAY command for the proper Source Emitter Output.
i.e. Right-click on command in Macro Command List and select Source 1 output)
9. Repeat for all zones and commands as required.
NOTE:
Remember: As in the example above, to make commands accessible no matter which source is
selected, you will need to PUNCH the command (Zone Level).
Command Name
Command Description
Parameter 1
Parameter 2
Zone Power Command
Discrete Power ON or OFF
Zone (1-8) (9-16)
PwrState (On, Off)
Zone Toggle Power Command
Power Toggle Command
Zone (1-8) (9-16)
N/A
Zone Volume Command
Set Volume to preset level
Zone (1-8) (9-16)
VolLevel (0 – 63)
Zone Volume Step Up Command
Increase Volume Setting
Zone (1-8) (9-16)
N/A
Zone Volume Step Down Command
Lower Volume Stetting
Zone (1-8) (9-16)
N/A
Zone Balance Level Command
Set Balance to Preset Setting
Zone (1-8) (9-16)
BalLevel (-15-15)
Zone Balance Step Up Command
Step Balance towards Rt. CH
Zone (1-8) (9-16)
N/A
Zone Balance Step Down Command
Step Balance towards Lt. CH
Zone (1-8) (9-16)
N/A
Zone Treble Level Command
Set Treble to Preset Setting
Zone (1-8) (9-16)
TrebLevel (-14dB-14dB)
Zone Treble Step Up Command
Increase Treble Setting
Zone (1-8) (9-16)
N/A
Zone Treble Step Down Command
Decrease Treble Setting
Zone (1-8) (9-16)
N/A
Zone Bass Level Command
Set Bass to Preset Setting
Zone (1-8) (9-16)
BassLevel (-14dB-14dB)
Zone Bass Step Up Command
Increase Bass Setting
Zone (1-8) (9-16)
N/A
Zone Bass Step Down Command
Decrease Bass Setting
Zone (1-8) (9-16)
N/A
Zone Source Select Command
Select Source for Zone
Zone (1-8) (9-16)
Source (1-8)
Zone Mute State Command
Discrete Mute ON or OFF
Zone (1-8) (9-16)
MuteState (On, Off)
Zone Mute Toggle Command
Mute Toggle Command
Zone (1-8) (9-16)
N/A
Zone Restore Balance Command
Restore Balance to Center
Zone (1-8) (9-16)
N/A
Zone Restore Treble Command
Restore Treble to Flat
Zone (1-8) (9-16)
N/A
Zone Restore Bass Command
Restore Bass to Flat
Zone (1-8) (9-16)
N/A
Zone Start Z Adjust Command
Enter ‘Zone Adjust’ Mode
Zone (1-8) (9-16)
N/A
Zone Set Max V Command
Set Maximum Zone Volume
Zone (1-8) (9-16)
N/A
Zone Adjust Done Command
Exit ‘Zone Adjust’ Mode
Zone (1-8) (9-16)
N/A
Zone Start Trim Adjust Command
Set Source Input Trim Setting
Zone (1-8) (9-16)
N/A
Turn Off All Zones Command
Power All Zones OFF
Zone (1-8) (9-16)
N/A
Set Max On V Command
Set Maximum ON Volume Setting
N/A
N/A
Table 2 – Internal Amplifier Commands
ZONE EXPANSION (CONNECTING MULTIPLE MRC88M CONTROLLERS)
Two MRC88m Controllers can be used to expand the number of zones in a MRC88m system to SIXTEEN. The
two MRC88m System Controllers interface via their
Expansion
port located on the rear of each Controller
[
Figure 3-(30)
].
