background image

Warranty and Return

WA–2

973-0031-01-01 Rev A

What does this warranty not cover?

This Limited Warranty does not cover normal wear and tear of the 

product or costs related to the removal, installation, or troubleshooting of the customer's electrical systems. This 

warranty does not apply to and Xantrex will not be responsible for any defect in or damage to:
a) the product if it has been misused, neglected, improperly installed, physically damaged or altered, either inter-

nally or externally, or damaged from improper use or use in an unsuitable environment;

b) the product if it has been subjected to fire, water, generalized  corrosion, biological infestations, or input voltage 

that creates operating conditions beyond the maximum or minimum limits listed in the Xantrex product specifi-
cations including high input voltage from generators and lightning strikes;

c) the product if repairs have been done to it other than by Xantrex or its authorized service centers (hereafter 

"ASCs"); 

d) the product if it is used as a component part of a product expressly warranted by another manufacturer;
e) the product if its original identification (trade-mark, serial number) markings have been defaced, altered, or 

removed.

Disclaimer

Product

THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY XANTREX IN CONNECTION WITH YOUR 
XANTREX PRODUCT AND IS, WHERE PERMITTED BY LAW, IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS, 
GUARANTEES, REPRESENTATIONS, OBLIGATIONS AND LIABILITIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE IN 
CONNECTION WITH THE PRODUCT, HOWEVER ARISING (WHETHER BY CONTRACT, TORT, NEGLIGENCE, PRINCIPLES OF 
MANUFACTURER'S LIABILITY, OPERATION OF LAW, CONDUCT, STATEMENT OR OTHERWISE), INCLUDING WITHOUT 
RESTRICTION ANY IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR 
PURPOSE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT 
REQUIRED UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD 
STIPULATED UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL 
DAMAGES, LOSSES, COSTS OR EXPENSES HOWEVER ARISING WHETHER IN CONTRACT OR TORT INCLUDING WITHOUT 
RESTRICTION ANY ECONOMIC LOSSES OF ANY KIND, ANY LOSS OR DAMAGE TO PROPERTY, ANY PERSONAL INJURY, ANY 
DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF MISUSE OR ABUSE, OR THE INCORRECT INSTALLATION, 
INTEGRATION OR OPERATION OF THE PRODUCT.

Exclusions

If this product is a consumer product, federal law does not allow an exclusion of implied warranties. To the extent you 

are entitled to implied warranties under federal law, to the extent permitted by applicable law they are limited to the 

duration of this Limited Warranty. Some states and provinces do not allow limitations or exclusions on implied 

warranties or on the duration of an implied warranty or on the limitation or exclusion of incidental or consequential 

damages, so the above limitation(s) or exclusion(s) may not apply to you. This Limited Warranty gives you specific 

legal rights. You may have other rights which may vary from state to state or province to province.

Warning: Limitations On Use

Please refer to your product manual for limitations on uses of the product. 

SPECIFICALLY, PLEASE NOTE THAT THE 

S

INE

 W

AVE

 P

LUS

 L

ONG

 AC C

ONDUIT

 B

OX

 

SHOULD NOT BE USED IN 

CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER MEDICAL EQUIPMENT OR DEVICES. WITHOUT LIMITING THE 
GENERALITY OF THE FOREGOING, XANTREX MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE USE OF THE 
XANTREX 

S

INE

 W

AVE

 P

LUS

 L

ONG

 AC C

ONDUIT

 B

OX IN CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER 

MEDICAL EQUIPMENT OR DEVICES.

Please note that the Sine Wave Plus Long AC Conduit Box is not intended for use as an uninterruptedly power supply 

and Xantrex makes no warranty or representation in connection with any use of the product for such purposes.

Summary of Contents for ACCB-L

































































Reviews: