background image

97-0020-01-01

9

Planning Preparations

This 

g

u

id

e for 

u

se by qu

alifi

ed installers only.

Figure 4

Wiring and Breakers Block Diagram for Freedom SW 2012 / 2024

2012 and 2024
Inverter/Charger

120 V AC OUT

120 V AC IN

Battery (Bank)
12 or 24 V

4 AWG

150 A fuse

†††

2/0 AWG

275 A fuse

††

8 AWG Chassis GND*

10 AWG

10 AWG

HOT = BLACK

NEUTRAL = WHITE

GND = GREEN/Bare

HOT BUS

HOT BUS

TO AC APPLIANCE
LOADS

MAIN ELECTRICAL PANEL

FROM SHORE OR
GENERATOR POWER

OPTIONAL
GFCI duplex receptacle special kit
15 A output limit

HARDWIRE CONNECTIONS
20 A MAX in inverter
30 A MAX in pass-through

Neutral

GND

15 A

20  A

Neutral

GND

30 A

MAIN

* Recreational Vehicles only. For Marine applications see NOTE below.

NOTE: The DC grounding conductor may be one size smaller than the minimum size conductor required for the DC current carrying conductors providing the overcurrent protection device in the DC 
positive conductor is rated no greater than 135% of the ampacity of the DC grounding conductor and the conductor is no smaller than 16 AWG.

††

 Class T or equivalent

    Freedom SW 2012

 In free air, as per NEC Table 310.17

  for 75 C rated copper conductor.

†††

 Class T or equivalent

     Freedom SW 2024

IMPORTANT:

Read Owner’s and In-

stallation Guides prior to installation.
Always refer to local and national
electrical codes for proper wire and
breaker sizes prior to installation.

Freedom SW 3K2K InvChg Install Guide.book  Page 9  Wednesday, October 12, 2011  4:40 PM

Summary of Contents for Freedom SW 815-2012















































































Reviews: