Xantrex LINK 2000-R Owner'S Manual Download

Page: 1 / 14

6/21/96

OWNERS MANUAL

LINK 2000-R IDEAL REGULATOR OPTION

Part # 890025

INSTALLERS! THIS DOCUMENT IS IMPORTANT FOR

OPERATION. PLEASE LEAVE IT WITH THE OWNER!

The

LINK 2000-R

is an integrated battery monitor, inverter/charger

controller, and advanced alternator regulator. This manual pertains

only to the alternator regulator features. All other features and

functions are described in the

LINK 2000

Owners Manual (Part #

890024). You must be familiar with that manual before using the

LINK 2000-R.

For use only with externally regulated

12 Volt "P" Field type alternators.

See Required Reading page 8.

All warranty issues must be resolved through Heart Interface or Cruising

Equipment Co. Please do not return to the retailer, or route warranty issues

through the retailer.

21440 68

Ave. So. Kent, WA 98032

(206) 872-7225 Toll Free 1-800-446-6180

Mfg. by

Cruising Equipment Co.

5245 Shilshole Ave. NW Seattle, WA 98107

(206) 782-8100

NEWREGINSTALL.PM6

Summary of Contents for LINK 2000-R















Search results

Summary of Contents for LINK 2000-R

Reviews:

Related manuals for LINK 2000-R

Brands by name

Popular brands

Xantrex LINK 2000-R, Owner'S Manual

Search results

Summary of Contents for LINK 2000-R

Reviews:

Related manuals for LINK 2000-R

Brands by name

Popular brands