background image

© 2001 Xantrex Technology Inc.  All Rights Reserved.

P/N  975-0013-01-01 Rev B  10/01

ii

About Xantrex

Xantrex Technology Inc., is a world-leading supplier of advanced power electronics and controls with products

from 50-watt mobile units to 1 MW utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and
backup power applications in both grid-connected and stand-alone systems.  Xantrex products include inverters,
battery chargers, programmable power supplies, and variable speed drives that convert, supply, control, clean, and
distribute electrical power.

Trademarks

Xantrex is a registered trademark of Xantrex Technology Inc.

Notice of Copyright

Stacking Interface Cable Installation Guide © October 2001 Xantrex International.  All rights reserved.

Disclaimer

While every precaution has been taken to ensure the accuracy of the contents of this guide, Xantrex

International assumes no responsibility for errors or omissions.  Note as well that specifications and product
functionality may change without notice.

Since the use of this manual and the conditions or methods of installation, operation, use and maintenance of

the unit are beyond the control of Xantrex Technology Inc., the company does not assume responsibility and
expressly disclaims liability for loss, damage, or expense arising out of or any way connected with such installation,
operation, use, or maintenance.

Due to continual improvement through product updates, photographs and/or illustrations used in this manual

may not 

exactly match your unit.  Xantrex Technology Inc., reserves the right to update this product without notice or

releasing an updated manual when 

fit, form or function are not affected.

Date and Revision

October 2001, Revision B

Part Number

975-0013-01-01

975-0013-01-01

975-0013-01-01

975-0013-01-01

975-0013-01-01

Contact Information

Web:

www.xantrex.com

Email:

drc@xantrex.com

Phone:

360/435.8826

Fax:

360/435.2229

Summary of Contents for SWI - INSTALLATION REV B























Reviews: