13
Parameter adjustment knob
Page 16
6.3. Parameter adjustment knob
1) Rotate the adjusting knob to adjust the parameters.
2) Rotating the adjusting knob clockwise increases the parameter value, and rotating the
adjusting knob counterclockwise decreases the parameter value.
3) When the adjusting knob is rotated the adjusted parameters are displayed in the
parameter display area.
6.4. Selection of working mode
1) Press the cutting mode selection button
while not cutting to switch between the
three cutting modes as needed: 2T, 4T and mesh cutting.
2) If the indicator
is on, it indicates that the machine is currently in 2T cutting mode.
3) If the indicator
is on, it indicates that the machine is currently in 4T cutting mode.
4) If the indicator
is on, it indicates that the machine is currently in mesh cutting mode.
6.5. Gas check function
1) Press the gas check button
while not in cutting state.
2) When the
indicator is lit, the machine is in gas check mode.
3) Press the gas check button again or wait 20s. After the indicator light goes out, the
machine has exited gas check mode.
Page 16
6.3. Parameter adjustment knob
1) Rotate the adjusting knob to adjust the parameters.
2) Rotating the adjusting knob clockwise increases the parameter value, and rotating the
adjusting knob counterclockwise decreases the parameter value.
3) When the adjusting knob is rotated the adjusted parameters are displayed in the
parameter display area.
6.4. Selection of working mode
1) Press the cutting mode selection button
while not cutting to switch between the
three cutting modes as needed: 2T, 4T and mesh cutting.
2) If the indicator
is on, it indicates that the machine is currently in 2T cutting mode.
3) If the indicator
is on, it indicates that the machine is currently in 4T cutting mode.
4) If the indicator
is on, it indicates that the machine is currently in mesh cutting mode.
6.5. Gas check function
1) Press the gas check button
while not in cutting state.
2) When the
indicator is lit, the machine is in gas check mode.
3) Press the gas check button again or wait 20s. After the indicator light goes out, the
machine has exited gas check mode.
Page 16
6.3. Parameter adjustment knob
1) Rotate the adjusting knob to adjust the parameters.
2) Rotating the adjusting knob clockwise increases the parameter value, and rotating the
adjusting knob counterclockwise decreases the parameter value.
3) When the adjusting knob is rotated the adjusted parameters are displayed in the
parameter display area.
6.4. Selection of working mode
1) Press the cutting mode selection button
while not cutting to switch between the
three cutting modes as needed: 2T, 4T and mesh cutting.
2) If the indicator
is on, it indicates that the machine is currently in 2T cutting mode.
3) If the indicator
is on, it indicates that the machine is currently in 4T cutting mode.
4) If the indicator
is on, it indicates that the machine is currently in mesh cutting mode.
6.5. Gas check function
1) Press the gas check button
while not in cutting state.
2) When the
indicator is lit, the machine is in gas check mode.
3) Press the gas check button again or wait 20s. After the indicator light goes out, the
machine has exited gas check mode.
Page 16
6.3. Parameter adjustment knob
1) Rotate the adjusting knob to adjust the parameters.
2) Rotating the adjusting knob clockwise increases the parameter value, and rotating the
adjusting knob counterclockwise decreases the parameter value.
3) When the adjusting knob is rotated the adjusted parameters are displayed in the
parameter display area.
6.4. Selection of working mode
1) Press the cutting mode selection button
while not cutting to switch between the
three cutting modes as needed: 2T, 4T and mesh cutting.
2) If the indicator
is on, it indicates that the machine is currently in 2T cutting mode.
3) If the indicator
is on, it indicates that the machine is currently in 4T cutting mode.
4) If the indicator
is on, it indicates that the machine is currently in mesh cutting mode.
6.5. Gas check function
1) Press the gas check button
while not in cutting state.
2) When the
indicator is lit, the machine is in gas check mode.
3) Press the gas check button again or wait 20s. After the indicator light goes out, the
machine has exited gas check mode.
Page 16
6.3. Parameter adjustment knob
1) Rotate the adjusting knob to adjust the parameters.
2) Rotating the adjusting knob clockwise increases the parameter value, and rotating the
adjusting knob counterclockwise decreases the parameter value.
3) When the adjusting knob is rotated the adjusted parameters are displayed in the
parameter display area.
6.4. Selection of working mode
1) Press the cutting mode selection button
while not cutting to switch between the
three cutting modes as needed: 2T, 4T and mesh cutting.
2) If the indicator
is on, it indicates that the machine is currently in 2T cutting mode.
3) If the indicator
is on, it indicates that the machine is currently in 4T cutting mode.
4) If the indicator
is on, it indicates that the machine is currently in mesh cutting mode.
6.5. Gas check function
1) Press the gas check button
while not in cutting state.
2) When the
indicator is lit, the machine is in gas check mode.
3) Press the gas check button again or wait 20s. After the indicator light goes out, the
machine has exited gas check mode.
Page 17
6.6. Electrical current settings for cutting
In cutting mode, the display window displays the current cutting current, which can be set by
turning the adjustment knob.
6.7. Protective indicators
The overheat indicator light
indicates that the machine has entered overheat protection
and has stopped output.
The over-current indicator light
indicates that the machine has entered over-current
protection and has stopped output.
6.8. Engineer mode
1) Press and hold the parameter adjustment knob
for 5s while not in cutting mode to
enter engineer mode.
2) After pressing for 1 second, the display window will count down from 3, then the machine
will enter engineer mode. Release the button during that time to exit the countdown without
entering engineer mode.
3) Engineer mode: F01: Standby time selection; 0, 5, 10, or 15, unit is min, 0 means that the
standby function is not enabled.
F02: Input over-voltage protection enabled; 0 means the function is off, 1
means the function is on.
F03: Post-flow time adjustment; 0-60s, precision is 1s.
F04: Torch length selection; 0, 5, 10, 15, or 20, unit is m, 0 means
self-adjusted.
4) After adjusting the parameters, press the cutting mode selection button
to save and
exit.
6.9. Restoring factory settings
1) Press and hold the cutting mode selection button
for 5s while not cutting to restore
factory mode.
2) After 1s, the display window will count down from 3. After completion, factory settings are
restored. Release the button halfway to exit the countdown without restoring factory settings.
3) Factory settings: Cutting mode: 2T continuous cutting; cutting current: rated maximum;
post-flow time: 15s.
Parameter adjustment knob
Gas check function
Electrical current settings for cutting
Protective indicators
