background image

 

 

-

 

Avoid contact with cables terminals when modules are exposed to light. 

-

 

Do not attempt to install or use a module with broken front cover glass or a 
perforated backsheet. 

 

-

 

Keep solar module(s) in original packing until point of assembly/installation to 
reduce risk of damage. 

-

 

Cover module face(s) completely with opaque material to halt the production 
of electricity when working with module wiring. Disconnect module(s) from 
other sources of electricity, such as batteries, when working on system. 

-

 

Avoid artificial or concentrated sunlight directed on module 

-

 

Avoid shadowing cells in order to prevent solar module hot spots and/or 
reduction in power. 

 

-

 

Newer touch the terminals with bare hands. 

-

 

Use insulated tools when wiring to solar module terminals, wear rubber gloves 
to eliminate shock or burn potential when wiring solar modules. 

 

 

Regardless of whether you are working on a new or existing roof, never allow 
the sheathing and metal parts to become wet.  

 

Protect the sheathing and metal parts from rain during the installation. Failure 
to do so may cause leaks. 

 

Work under dry conditions with dry tools. 

 

Avoid installing modules and mounting system in high corrosion areas. 

 

 

Do not install near flammable gases. 

 

APPLICATION 

ASOL-250P-WSR modules are designed to provide high-power output for roof mounted/building integrated 
photovoltaic  systems  as  well  as  in-grid  systems.  The  modules  are  assigned  to  the  Application  class  A  (in 
accordance with IEC 61730). The modules thus fulfil the requirements of Protection class II. 

Summary of Contents for ASOL-250P-WSR











Reviews: