manualshive.com logo in svg

Xerox ColorQube 9303 Series, Service Manual


Share
Download
background image

February 2013

xiv

ColorQube® 9303 Family

Translated Warnings

Introduction

DANGER: Exécuter cette procédure avec précaution. Les moteurs peuvent devenir très 
chauds en fonctionnement normal.

AVVERTENZA: procedere con cautela durante questa procedura. I motori si riscaldano 
molto durante il funzionamento.

VORSICHT: Bei diesem Vorgang vorsichtig vorgehen, da Motoren im Normalbetrieb heiß 
werden können.

AVISO: Tenga cuidado al efectuar este procedimiento. Los motores alcanzan altas tem-
peraturas durante su funcionamiento normal.

WARNING

Take care during this procedure. The drum will become hot during normal operation.

DANGER: Faites attention pendant cette procédure. Dans des conditions normales de 
fonctionnement, le tambour devient chaud.

AVVERTENZA: Prestare attenzione durante questa procedura. Il tamburo diventa caldo 
durante il normale funzionamento.

VORSICHT: Die Trommel wird im Normalbe¬trieb heiß.

AVISO: Tome precauciones durante el procedimiento. El cilindro tendá una temperatura 
elevada durante el funcionamiento normal.

WARNING

Take care during this procedure. The registration/preheat assembly will become hot 
during normal operation.

DANGER: Exécuter cette procédure avec précaution. Le module de cadrage/préchauff-
age peut devenir très chaud en fonctionnement normal.

AVVERTENZA: procedere con cautela durante questa procedura. Il complessivo di reg-
istrazione/preriscaldamento raggiunge alte temperature durante il funzionamento.

VORSICHT: Bei diesem Vorgang vorsichtig vorgehen, da das Ausrichtungsmodul/
Vorheizaggregat im Normalbetrieb heiß wird.

AVISO: Tenga cuidado al realizar este procedimiento, ya que el conjunto de registro/pre-
calentamiento alcanza una elevada temperatura durante su funcionamiento normal.

Mechanical Warnings

WARNING

Do not remove the DADH while the DADH is lowered. In the lowered position the coun-
terbalance springs are compressed and can cause injury when released.

DANGER: Ne pas retirer le CAD alors qu'il est en position basse. Dans cette position, les 
ressorts compensateurs sont compressés et peuvent entraîner des blessures s'ils se 
relâchent.

AVVERTENZA: non rimuovere l'alimentatore automatico documenti quando è 
abbassato. In questa posizione, le molle del contrappeso sono compresse e possono 
causare lesioni al rilascio. 

VORSICHT: Vorlageneinzug nicht in abgesenkter Position entfernen. Bei abgesenktem 
Vorlageneinzug sind die Ausgleichsfedern zusammengedrückt und können bei Fre-
igabe Verletzungen verursachen. 

AVISO: No quite el alimentador de documentos automático si está bajado. Cuando está 
bajado, los resortes de contrapeso están comprimidos y pueden causar lesiones al 
soltarse. 

WARNING

Keep away from the crease blade mechanism when working in close proximity to the 

booklet maker while the machine is powered on. The crease blade mechanism activates 
quickly and with great force.

DANGER: Ne pas s'approcher du méchanisme de la lame de pliage lors d'une activité à 
proximité de la plieuse/brocheuse pendant que la machine est sous tension. Ce mécan-
isme s'active rapidement et avec force.

AVVERTENZA: Quando la macchina è accesa, tenersi a debita distanza dalla lama di pie-
gatura mentre si opera in prossimità della stazione libretto. Il meccanismo della lama di 
piegatura si attiva con velocità e forza notevoli. 

VORSICHT: Wenn bei eingeschaltetem Gerät nahe am Booklet Maker gearbeitet wird, 
von der Schneidevorrichtung fernhalten. Die Schneidevorrichtung wird schnell und mit 
viel Druck ausgelöst. 

AVISO: Manténgase apartado del mecanismo de la cuchilla hendedora cuando trabaje 
junto al realizador de folletos si la máquina está encendida. Dicho mecanismo se activa 
de forma rápida y con mucha fuerza.

WARNING

Take care during this procedure. Sharp edges may be present that can cause injury.

DANGER: Exécuter cette procédure avec précaution. La présence de bords tranchants 
peut entraîner des blessures.

AVVERTENZA: procedere con cautela durante questa procedura. Possono essere pre-
senti oggetti con bordi taglienti pericolosi. 

VORSICHT: Bei diesem Vorgang vorsichtig vorgehen, damit keine Verletzungen durch 
die scharfen Kanten entstehen. 

AVISO: Tenga cuidado al efectuar este procedimiento. Puede haber bordes afilados que 
podrían producir lesiones. 

WARNING

Take care during this procedure. The stripper blade is very sharp and can cause injury.

DANGER: Effectuez cette procédure avec précaution. La lame du doigt décolleur est 
très tranchante et peut être source de blessures.

AVVERTENZA: Fare attenzione durante questa procedura. La lama del separatore è 
molto tagliente e può causare lesioni personali.

VORSICHT: Bei diesem Vorgang vorsichtig vorgehen. Die Abstreifklinge ist sehr scharf 
und es besteht Verletzungsgefahr.

AVISO: Tenga cuidado durante este procedimiento. El conjunto de dedos de despegue 
es muy filudo y puede producir lesiones.

Summary of Contents for ColorQube 9303 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ColorQube 9303 Series

Canon iR1018 Portable Manual preview
iR1018
Brand: Canon Pages: 86
Canon iR1018 Installation Procedure preview
iR1018
Brand: Canon Pages: 20
Xerox 7142 Service Manual preview
7142
Brand: Xerox Pages: 341
Magicard Prima Brochure preview
Prima
Brand: Magicard Pages: 6
UBI EasyCoder 501 SA Service Manual preview
EasyCoder 501 SA
Brand: UBI Pages: 214
UBI EasyCoder 401 Technical Manual preview
EasyCoder 401
Brand: UBI Pages: 64
Xerox 7300DX - Phaser Color Laser Printer Specification preview
7300DX - Phaser Color Laser Printer
Brand: Xerox Pages: 14
Tally T2150 SprintPro Maintenance Manual preview
T2150 SprintPro
Brand: Tally Pages: 124
Oce VarioPrint 6180 User Manual preview
VarioPrint 6180
Brand: Oce Pages: 306
Glunz & Jensen NewsWriter XL Operating Manual preview
NewsWriter XL
Brand: Glunz & Jensen Pages: 104
Xerox VersaLink Series System Administrator Manual preview
VersaLink Series
Brand: Xerox Pages: 185
Xerox CopyCentre C65 Quick Reference Manual preview
CopyCentre C65
Brand: Xerox Pages: 150
Kyocera Mita Ecosys FS-1800+ Installation Manual preview
Ecosys FS-1800+
Brand: Kyocera Mita Pages: 31
Seiko Epson P130A Manual preview
P130A
Brand: Seiko Epson Pages: 301
Xerox Nuvera 100 MX Brochure preview
Nuvera 100 MX
Brand: Xerox Pages: 4
Canon Pixma TS201 Online Manual preview
Pixma TS201
Brand: Canon Pages: 189
Canon PIXMA TS3160 Online Manual preview
PIXMA TS3160
Brand: Canon Pages: 293
Canon PIXMA TS302 Online Manual preview
PIXMA TS302
Brand: Canon Pages: 341

Brands by name

Popular brands

Load more brands