Xerox D95 User Manual Download | Manualshive

Page: 118 / 460

background image

The following actions terminate the storing process:

• Pressing the Interrupt button on the control panel
• The Auto Reset feature causes a time-out
• A popup window (paper jam, for example) displays

Note

Do not perform the following while storing a program; otherwise, the program may
not be stored or may not function as programmed:

• Remove or insert a paper tray
• Load or reload paper in Tray 5 (Bypass)

2. From the Setup and Calibration, Setup, Tools section, select Stored Programming.
3. Select the following:

a) Store
b) Select a Stored Programming button from the numbered list. (Select the up and

down arrows to display the previous or next screen.)

Tips when storing a program:

• When storing a program for Tray 5, store both the paper size and the paper type

or the stored program may not be successfully called.

• Once a job is stored to a button it cannot be edited, it must be saved again.

4. Set the additional features. Features that are not available to use with Stored

Programming will be grayed out, such as Network Scanning and Job Flow Sheets.
Continue to select the Copy button and OK.

• Feature and OK button availability will depend on what buttons were enabled

by the System Administrator.

• A tone is generated while registering to job memory. To change the tone volume,

refer to “Stored Programming Tone” in the System Administration Guide.

5. From the Copy window, select 1 ->2 Sided copying.
6. From the Output window, select the Watermark button.
7. From the Watermark screen:

a) Select On.
b) Mark the Date & Time box.
c) Select Save.

8. Press the Start button to end registration and store the programming. Once you call

the copy job programming, all the screens that you programmed display prior to job
submission.

• One-touch buttons M01 to M40 are provided for Stored Programs 1-40.

User Guide

8-2

Stored Programming

«
...
116
117
118
119
120
...
»

Summary of Contents for D95













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for D95

Brand: Panasonic Pages: 270

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 41

Brand: Panasonic Pages: 114

Brand: Panasonic Pages: 114

Brand: Panasonic Pages: 138

Brand: Panasonic Pages: 161

Brand: Panasonic Pages: 271

Brand: Xerox Pages: 8

CopyCentre C2128

Brand: Xerox Pages: 197

Brand: Gestetner Pages: 73

2006NPC - DocuColor Color Laser

Brand: Xerox Pages: 574

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands