Xerox D95 User Manual Download | Manualshive

Page: 238 / 460

background image

a) Make the desired selections for Paper Type/Paper Weight, Paper Size, and Paper

Color.

b) If necessary, make the desired changes to paper curl and alignment adjustment.

Note

Refer to the System Administration Guide for detailed information on the paper
curl and alignment adjustment options.

c) Select Save until you are returned to the tray settings window.

11. Select Confirm to close the window.

Skew adjustment levers

The skew adjustment levers are found in all paper trays. These levers are used to improve
paper feed accuracy and to reduce paper skew problems.

1.

Rear skew adjustment lever

2.

Right-side skew adjustment lever

• These levers should remain in their default position. The position of these levers

should be changed only when there is a skew problem when running a specific print
job and/or specific media type.

• Changing the skew adjustment levers from their default position may cause more

skew problems when running certain media types, such as coated, label, transparency,
and film.

Use the following procedure to set the skew adjustment levers.
1. Pull out the tray slowly until it stops.
2. Slide the rear skew adjustment lever to the right.
3. Gently push in the tray until it comes to a stop.
4. From the Tray Properties window, enter the correct paper information, including size,

type, weight, and if necessary, paper curl and/or alignment option.

5. Select OK to save the information and close the Tray Properties window.

User Guide

18-8

Oversized High Capacity Feeder (OHCF), 1 or 2 trays (Trays 6/7)

«
...
236
237
238
239
240
...
»

Summary of Contents for D95













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for D95

Brand: Olivetti Pages: 753

Brand: Olivetti Pages: 297

Brand: Olivetti Pages: 242

Brand: Xerox Pages: 123

Brand: Toshiba Pages: 9

Brand: Toshiba Pages: 48

Brand: Toshiba Pages: 78

Brand: Toshiba Pages: 84

Brand: Toshiba Pages: 75

Brand: Toshiba Pages: 84

Brand: Toshiba Pages: 95

Brand: Toshiba Pages: 124

Brand: Toshiba Pages: 130

Brand: Toshiba Pages: 150

Brand: Toshiba Pages: 171

Brand: Toshiba Pages: 166

Brand: Toshiba Pages: 180

Brand: Toshiba Pages: 190

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands