Xerox D95 User Manual Download | Manualshive

Page: 50 / 460

background image

9. Offset Stacking places each stack of printed pages slightly to the left or right of the

previous stack for easier separation.
a) Select Output /Offset.
b) Select Center Tray Upper or Center Tray Lower. For automatic creasing, select

Right Middle Tray.

c) Select Offset Stacking, then select System Default, No Offset, Offset Per Set or

Offset Per Job, then select Save.

10. Select Save.

Perfect Binding (optional)

Important

The Perfect Binder is available with the D110, D125, and D136 Copier/Printer. The
copier/printer must use the integrated controller and not a separate print server.

Note

The Layout Adjustment options may be useful when the completed output is a perfect
bound book.

When the optional Perfect Binding feature is On, the following options are available:

Covers

Choose one of three options:

• Blank Cover: Select this option either for blank covers (front and back) or when using

preprinted covers.

• Print on Both: Select this option when printing on front and back covers and on both

the inside and outside of the covers.

• 1 Sided Covers, Print on Outside: Select this option to print only on the outside of

the front and back covers.

Cover & Book Block Size/Paper Supply

This option allows you to set the size of both the Cover and the Book Block pages and
to select from which tray the paper will be supplied.

• Cover Size: Select the paper size of the book cover from either the standard sizes

(such as 11 x 17 in./A3) or set a custom size.

• Book Block Size: Select the paper size of the book block pages from the standard

sizes (such as 11 x 17 in./A3) or set a custom size.

• Paper Supply: Select the tray to use for both the cover and book block pages; these

will be two different trays (one for the cover and another for the book block pages).

User Guide

4-12

Copy

«
...
48
49
50
51
52
...
»

Summary of Contents for D95













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for D95

Brand: Xerox Pages: 176

Brand: Oce Pages: 68

Brand: Oce Pages: 156

Brand: Sharp Pages: 4

AL-1010 - B/W Laser - Copier

Brand: Sharp Pages: 12

Brand: Sharp Pages: 30

AL-1041 - B/W Laser Printer

Brand: Sharp Pages: 47

AL 1000 - B/W Laser Printer

Brand: Sharp Pages: 47

Brand: Sharp Pages: 50

AL 800 - B/W Laser - Copier

Brand: Sharp Pages: 51

Brand: Sharp Pages: 93

Brand: Sharp Pages: 70

Brand: Panasonic Pages: 153

Brand: Avision Pages: 51

Brand: Avision Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands