background image

Color Management Guide

 1-1  

 

Color Management 
Overview

The CMS (Color Management System) Option Tool is an add-on software for the Xerox 490/980 
Color Continuous Feed Printing System, and it can be installed on a remote PC. The CMS Option 
Tool is the primary tool used when adjusting color on the Xerox 490/980 Color Continuous Feed 
Printing System. Color selections and calibrations are performed using the CMS Tool. This 
section explains what the CMS Option tool is and how to make color selections for a specified 
job on the PC-GUI.

The Xerox 490/980 Color Continuous Feed Printing System produces what is commonly known 
in the industry as "Business" or "Transactional Color". This is one way to describe this caliber of 
color and where it fits in the market; between that of ink jet products and offset quality. The 
machine is also the fastest toner-based production color system available today. Utilizing four 
color housings, the machine outputs CMYK at 600dpi, and line screens from 85 to 300 lpi. Color 
output of this machine is richer in tone and hue than comparable ink jet systems. The color 
gamut is targeted at newsprint-type image quality. 

Because the machine uses dry toner, it can print on a wide variety of substrates ranging from 64 
gsm to 160 gsm. Paper weights lighter than 64 gsm may also be used subject to satisfactory 
testing for suitability. Light weight stocks are typically a problem for ink jet printers because the 
ink often causes water saturation, curling, and other issues. Through the use of dry toner and 
flash fusing technology, the machine provides a competitive advantage to the customer. 
Because of its unique use of strobing xenon lamps, only the toner is heated and no pressure, 
heat or contact is made with the substrate itself. Therefore, the customer gains the ability to 
use light weight stocks and other special media, such as cards and adhesive labels, without any 
of the problems associated with the use of ink jet systems.

1

Summary of Contents for Document Centre 480







































































































Reviews: