Xerox DocuPrint N2025 Service Manual Download

Page: 270 / 378

02/2000

6-38

DocuPrint N2025/N2825

GP 3.4, GP 3.5

Initial Issue

General Procedures / Information

Speed - Ethernet Menu setting to select the speed of the 10/100Base-Tx Ethernet interface.
The default setting of “Auto” allows the card to automatically sense the speed of the Ethernet
as either 10 or 100 Mbits, automatically sense duplex mode as either half or full. The setting of
10/Half or 10/Full forces the card to operate at 10 Mbits in either half or full duplex mode. The
setting of 100/Half or 100/Full forces the card to operate at 100Mbits in either half or full duplex
mode.

Speed - Token Ring Menu setting for the default ring speed for the Token Ring interface.

Source Routing - Menu setting in the Token Ring menu to select the source routing option.

Subnet Mask - Menu setting in the Ethernet or Token Ring menu to manually set the 4 Subnet
Mask address bytes. This setting is common between the Ethernet and Token Ring menus.
This item only appears if "IP Address Res” is set to “Static.”

Symbol Set - Menu setting for the default font symbol set used in PCL.

System Menu - Menu selection to invoke the "System Menu."

Print Menu - Menu selection to invoke the "Print Menu."

Test Print - Print a test pattern which can be used by service engineers (and users) to analyze
print quality. Will cause a printer reset. It will be printed using the PCl number of Print Quantity,
default source and default type. All test prints are printed at 600x600 DPI.

Token Talk Enable - Token Ring menu setting to enable Token Talk protocol.

Token Ring Menu - Menu selection to invoke the Token Ring menu.

Tray Menu - Main Menu selection to access tray settings that are common to all system lan-
guages (PCL and PostScript).

Tray Sequence - Tray Menu setting defining the order in which trays are used when more than
one tray meets the size and type requirements.

Tray x Mode - Tray Menu setting to select the paper size installed in this tray is automatically
detected by the printer, or if the auto detection mechanism is overridden by the values loaded
in the Custom Size entry.

Tray x Type - Tray Menu setting defining the type of paper installed in each tray. Since the
printer cannot sense the type of paper installed, this parameter must be entered manually for
each tray. There is a separate entry for each tray installed.

USB PDL - Menu setting for the default emulation for the USB port.

XIE - Menu setting to select the default image (resolution) enhancement mode used in PCL
and PostScript.

GP 3.5 Non-Menu Control Panel States

Printer States

After power is turned on, the printer cycles through Power On Diagnostics, Initialization and
Warming Up states before entering the Ready state. The following is the display indication for
each state (Table 1). All states defined in Table 1 are mutually exclusive.

Table 1 Power-Up Sequence Display Messages

State

Description

Display

P/O Diag.

See Ref. 12

Initializing

This state commands the IOT to warm up, starts all
system tasks, loads NVM parameters into the cur-
rent configuration table and starts connectivity proto-
cols.

Top Line: Initializing
Bottom Line:

Warming-up

For the case where the IOT is already warmed up,
the display may change from Initializing to Ready,
and bypass this display.

Top Line: Warming Up
Bottom Line:

Ready

In this state, the printer is ready to accept and print
data from any enabled port. It may be overridden by
higher priority messages requiring operator interven-
tion such as paper jams or load paper requests. The
message may be overridden by the PJL "RDYMSG"
command.

Top Line: Ready
Bottom Line:

Processing

This state is entered when PostScript or PCL is pro-
cessing a job. It is overridden by higher priority mes-
sages such as paper jams or load paper requests or
by the PJL "RDYMSG" command. The Tray No. cur-
rently in use is displayed on the bottom line. The Tray
number message is alternated with the "Job Name"
on the second line if a name was supplied with the
PJL "JOB" command.

Top Line: Processing
Bottom Line: <job
name>
<Tray x>

Waiting

This state occurs when either PostScript or PCL is
waiting for input data as defined in the PCL and
PostScript Job Flow diagrams. It is overridden by
higher priority messages such as paper jams or load
paper requests or by the PJL "RDYMSG" command.
The Tray number currently in use is displayed on the
bottom line. The Tray number message is alternated
with the "Job Name" on the second line if a name
was supplied with the PJL "JOB" command.

Top Line: Waiting
Bottom Line: <job
name>
Bottom Line: <Tray x>

Flushing

This state occurs in PostScript when flushing a job
due to a PostScript error or PostScript "Interrupt"
command (Control-C). It is not overridden by the PJL
"RDYMSG," but is overridden by operator interven-
tion conditions, the "Canceling Job" message and
manu selections. The "job name" appears on the
second line if a name was supplied with the PJL
"JOB" command.

Top Line: Flushing
Bottom Line: <job
name>