2 - 54
Phaser 840/850/860/8200 Color Printer - Service Manual
8,002.67
CAP_PROG_FAULT(22)
Generic Cap Task Program Fault. This error indicates that the
main CAP state sequencer, cap_main(), has entered the program
fault state. There are multiple reasons that this can happen.
Genereally they involve unexpected conditions while performing
CAP movements; home, goto, etc.
08,003.46
The cap-home sensor was activated too soon. This can occur if
the cap/wipe/purge assembly was obstructed while moving up
and therefore retruned to the home position too soon. Ensure that
the head tilt mechanism is working properly. Run diagnostics to
verify cap drive motion and alignment.
08,009.65
An unexpected message was received while homing the
Cap/Wipe/Purge assembly, usually during system initialization.
This fault is due to a failure of the Y-Axis Encoder
8,022.60
CAP_PROG_FAULT(22)
Unexpected CAP Command in Idle State. An invalid CAP
command or unknown ITC message was received by the CAP
task, while it was in the idle state.
9,000: INK LOADER: INK MELTERS AND PRINTHEAD INK-LEVEL SENSORS.
9,001.45:
IL_FAULT_C_
TWANGER
Malfunction of the ink-level sensor in the cyan reservoir. Replace
the printhead.
9,002.46:
IL_FAULT_M_
TWANGER
Malfunction of the ink-level sensor in the magenta reservoir.
Replace the printhead.
9,003.47:
IL_FAULT_Y_
TWANGER
Malfunction of the ink-level sensor in the yellow reservoir.
Replace the printhead.
9,004.48:
IL_FAULT_K_
TWANGER
Malfunction of the ink-level sensor in the black reservoir. Replace
the printhead.
9,005.40:
IL_FAULT_C_JAM
The cyan ink-melt heater is on, but ink does not seem to be
dripping. Check that the ink stick is able to advance in the chute.
An ink stick jam will be reported three times before an ink-melter
fault is declared. Replace the ink loader. If the problem persists,
replace the power supply. ***see SF157***
9,006.41 and
9,069.41:
IL_FAULT_M_JAM
The magenta ink-melt heater is on, but ink does not seem to be
dripping. Check that the ink stick is able to advance in the chute.
An ink stick jam will be reported three times before an ink-melter
fault is declared. Replace the ink loader. If the problem persists,
replace the power supply. ***see SF157***
9,007.42 and
9,037.42:
IL_FAULT_Y_JAM
The yellow ink-melt heater is on, but ink does not seem to be
dripping. Check that the ink stick is able to advance in the chute.
An ink stick jam will be reported three times before an ink-melter
fault is declared. Replace the ink loader. If the problem persists,
replace the power supply. ***see SF157***
Table 2-4 Front Panel & Fault History Log Error Codes and Messages
Error code
Definition
Summary of Contents for Phaser 840
