Xerox Telecopier 7032 Service Manual Download

Page: 144 / 286

6. General Procedures/Information

Section Contents

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1

6.1 General Procedures

6.1.1

G3 PWB Setup (USO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2

6.1.2

G3/Coupler Setup (RX) . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2

6.1.3

Paper Tray Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.1.4

RAM/ROM Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

6.2 Diagnostic Procedures

6.2.1

Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-7

6.2.2

Auto Diagnostics (Self Test) . . . . . . . . . . . . . . . . . . . . . . . 6-7

6.2.3

Remote Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

6.2.4

Service Mode Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

6.2.5

Test 04, Service Mode Options Report

. . . . . . . . . . . . . 6-15

6.2.6

Test 08, Service Mode Diagnostics . . . . . . . . . . . . . . . . . 6-16

6.3 Product Specifications

6.3.1

Product Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-18

6.3.2

Physical Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . .

6-18

6.3.3

Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-18

6.3.4

Electrical Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . .

6-19

6.3.5

Environmental Specifications

. . . . . . . . . . . . . . . . . . . . . 6-19

6.3.6

Recording Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-19

6.3.7

Donor Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-19

6.3.8

Original Stacking Requirements

. . . . . . . . . . . . . . . . . . . 6-19

6.4 Tools and Supplies

6.4.1

Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20

6.4.2

Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20

6.5 Installation (7033/7033S) and Removal

6.5.1

Kit Contents (RX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20

6.5.2

Installing the Terminal

. . . . . . . . . . . . . . . . . . . . . . . . . . .

6-21

6.5.3

Removing/Shipping the Terminal

. . . . . . . . . . . . . . . . . 6-24

6.6 General Information

6.6.1

Telephone Requirements (USO) . . . . . . . . . . . . . . . . . . . 6-24

6.6.2

Electrostatic Discharge Precautions . . . . . . . . . . . . . . . . 6-25

6.6.3

Glossary of Mnemonics . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-25

6.7 Change Tag/MOD Information

6.7.1

Tag/MOD Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-26

6.7.2

Assembly and Firmware Matrix

. . . . . . . . . . . . . . . . . . .

6-34

Introduction

The following is a description of the information contained within this
section of the service manual.

The General Procedures subsection contains information relating to
setting up the G3 PWB and the paper tray.

All of the available diagnostic procedures are described in 6.2.

When a problem exists in a terminal that could be caused by conditions
outside of the defined specifications, refer to Product Specifications. If
the problem is a result of space, electrical, or environmental problems,
call for assistance.

The Tools and Supplies subsection contains a listing of the required tools
and supplies needed to properly repair and maintain the terminal.

The Installation subsection provides the procedures required to install
and verify basic operation of the terminal. The procedure for repacking
the terminal for shipment is also provided.

The General Information subsection contains requirements for
telephones and interconnections. Refer to Telephone Requirements
whenever the problem is a result of the telephone or telephone
connections. This section also contains precautions concerning
electrostatic discharge and a Glossary of Mnemonics.

As changes in configuration are made to the terminal, they are assigned
a Tag/MOD number. Information about a specific modification can be
found in the Tag/MOD Index within the Change Tag/MOD Information
subsection. This section also contains terminal configuration
information in Assembly and Firmware Matrix.

6/92

Telecopier 7032 / 7033 Service Manual

6-1

Section Contents, Introduction

www.printcopy.info