1.5 Installation
1.5.1 LAN Fax Server Option (Ethernet Version)
Note:
Before installing the Fax Server PWB enter the Service Mode and
obtain a copy of the Options Report. From the Report and table
below confirm that the required Firmware levels to support the
option are installed into the terminal.
Note:
The LAN Fax Server option can not co-exist with any other
option already installed in the terminal. Before installing this
option remove all other existing options connected to the
Option Mother PWB.
1.
This option requires a terminal with firmware level 6.01 (Tag 15) or
higher.
2.
Obtain an Options Report. Verify the Rom Program Version to the
following:
ROM NAME
VERSION
Ram/Rom PWB
MR0
6.01/4400
MR1
6.01/BB00
MR2
6.01/6F00
MR3
6.01/B800
FT0
6.01/7900
G3 PWB
G3M
6.01/0E00
3.
Install the auxiliary tray if not already installed. If the auxiliary tray
option contains a firmware upgrade kit, install only the firmware
listed in step 2.
Note:
Some auxiliary tray option kits have lower level firmware and
late production option kits have the firmware upgrade kit
deleted.
The auxiliary tray is part of the base RX 7033 terminal and is not
considered as an option.
4.
Perform a Diagnostic Self Test to verify correct machine operation.
Note:
During the installation of the hardware the network supervisor
can be installing the software onto the network following the
procedures in the Supervisors Handbook.
5.
Remove the Fax Server PWB and mother PWB options, external
power supply (If provided), access cover, EMI shield, manuals,
hardware, and software disks from the shipping carton.
6.
Disconnect the power cord from the terminal.
7.
Disconnect the telephone line and handset cord.
8.
Remove the screw securing the Access cover, then remove the plastic
and metal covers.
9.
If not already installed, install the Option Mother PWB. Set the PWB
on the guide and slide it to the left to connect P1 to J230 on the
main PWB. Secure the upper right corner of the PWB to the
electrical box using the hardware provided with the option.
10. The Fax Server PWB is factory set for Ethernet thin cable type (Refer
to figure 1). If the network is Ethernet thick or 10 BaseT proceed to
step 11. If installing on a Ethernet thin cable type proceed to step
12.
11. Locate the Ethernet Thick/Thin and RJ45 (10 BaseT) jumper J3 on the
Fax Server PWB and select either the thick or 10 BaseT position
(Refer to figure 1).
6/92
1.5, 1.5.1
8h-16
Telecopier 7032 / 7033 Service Manual
www.printcopy.info
www.printcopy.info
Summary of Contents for Telecopier 7032
