1.3.1
Prepare for System Checks
1. Look for any obvious problems such as a
paper jam, original document jam, or
telephone or data cable connections
loose at the terminal jacks or wall jack.
2. Ensure that the handset is on the handset
cradle. Ensure that the power cord is
connected to the terminal and to the wall
outlet.
N O T E : I f u n a b l e t o p e r f o r m a n y o f t h e
following steps or an error message prohibits
other display indications, go directly to 1.3.2
Off-Line System Check.
3. Enter the service mode.
RX NOTE: Refer to section 6.2 for
procedure to enter and exit the service
mode.
a.
Close Flip Panel.
b.
Press Exit.
c.
Press
*
on the key pad three times.
cd Press Stop.
e.
If the terminal is in secure mode,
repeat steps a, b, and c.
f.
The top line of the display flashes to
indicate that you are in the service
mode.
LOAD ORIGINALS FACE DOWN
TIME ENTER TERMINAL ID/NAME
NOTE: If ENTER TERMINAL ID/NAME appears
in the display, programming of local terminal
name and ID is required.
4. Print the service mode options report.
Save the report for Final Actions.
a.
Press 0 and 4 on the keypad, then
press Enter. The display indicates:
04 OPTIONS REPORT PRINT
PRESS [START] OR [STOP]
b.
Press Start. The terminal prints the
service mode options report while
the display indicates:
04 OPTIONS REPORT PRINTING
PRESS [STOP] TO END
NOTE: If options report does not print,
proceed to Off-Line System Check.
5. Set “Listen to Dial” to on.
RX NOTE: Only set Listen to Dial on if you
are permitted to listen to dial tones in
your country.
a.
Open the flip panel. The display
indicates:
PRESS APPROPRIATE BUTTON(S) TO
MAKE
b.
Press Sound Control. The display
indicates:
LISTEN TO DIAL, PANEL TONE,
SPEAKER
c.
LISTEN TO DIAL
should be flashing. Press
Enter. The display indicates:
LISTEN TO DIAL> OFF, ON
PRESS [SELECT] THEN [ENTER] OR
d.
Press Select. When
ON
is flashing,
press Enter.
e.
Press Exit, then close the flip panel.
6. Exit the service mode.
a.
Press Exit.
b.
Press
*
on the key pad three times.
c.
Press Stop.
d.
The top line of the display stops
flashing.
7. Perform the Off-Line System Check, 1.3.2.
8/91
Telecopier 7032 / 7033 Service Manual
1-3
1.3.1
www.printcopy.info
www.printcopy.info
Summary of Contents for Telecopier 7032
