12.
Close the flip panel. Place an original
(test pattern 82P151) into the ADF face
down.
After the original is inserted, the display
indicates:
SELECT FEATURES THEN DIAL OR
RESERVE JOB
Y
N
|
Check the ADF document sensor (RAP
2.20). Replace main PWB.
13. Hold the original in place so it will not
feed until the nudger solenoid actuates.
Press Copy, then press Start.
Nudger solenoid actuates approximately
4 seconds after Start is pressed.
Y
N
|
Replace in order: nudger solenoid,
main PWB.
14. When nudger solenoid actuates, release
the original.
NOTE: If the original is not released
within 4 seconds after the solenoid
actuates, a misfeed will be detected.
Document feeds normally through the
scanner and into the output tray.
Y
N
|
Perform RAP 2.10.
15.
The image quality on the copy is
acceptable (compare to the test pattern
sample in section 3).
Y
N
|
Perform RAP 2.17.
16. Customer problem is a malfunctioning
option.
Y
N
|
Perform the On-Line System Check,
1.3.3.
17. Go to Additional Checks in section 1.3.4
to select appropriate test.
1.3.3 On-Line System Check
NOTE: Perform this check only after the Off-
Line System Check has been performed.
NOTE: If an error code (CXXX, EXXX, FCXX,
FPXX, or OPXX) appears at any time during
this check, do not continue. Refer to section 2
for the error code List, and perform the actions
indicated.
RX NOTE: If it is not permitted to listen to dial
tones in your country, go to step 2.
1. Perform the following:
a.
Ensure the handset and telephone
line cords are connected.
b.
Perform a send operation to a known
good G3 facsimile terminal that is set
to auto receive.
The dial tone is heard when the terminal
goes on-line.
Y
N
|
Perform RAP 2.18.
2. Dialing completes successfully.
Y
N
|
Replace in order: G3 PWB, main
PWB.
3. The display indicates:
SENDING DOCUMENT
(SPEED)
(RECEIVER
Y
N
|
Perform RAP 2.16.
4. The display indicates that the terminal is
sending in G2 mode (CCITTG2).
Y
N
|
Go to step 6.
5. Replace in order: modem PWB, G3 PWB.
6.After completion of the send operation, the
display indicates:
SEND OPERATION COMPLETE
#
TIME
DATE
Y
N
|
Replace in order: G3 PWB, modem
PWB, main PWB.
7. The image quality received at the remote
terminal is acceptable. (Image quality
acceptance is determined by the remote
operator.)
Y
N
|
Perform RAP 2.16.
8. Call the terminal from another
telephone. The terminal answers with
ready tones.
Y
N
|
Perform RAP 2.19.
9. Perform a receive operation. The
terminal receives normally, and the
display indicates:
LOAD ORIGINALS FACE DOWN
TIME
DATE
Y
N
|
Replace in order: G3 PWB, modem
PWB, main PWB.
10. The image quality received is acceptable
(refer to Image Quality Section 3).
Y
N
|
Perform RAP 2.16.
11. Customer problem has been resolved.
Y
N
|
Go to Additional Checks in section
1.3.4 to select appropriate test.
12. Go to Final Actions.
6/92
Telecopier 7032 / 7033 Service Manual
1-5
1.3.3
www.printcopy.info
www.printcopy.info
Summary of Contents for Telecopier 7032
