Xerox WorkCentre 5687 Series Service Manual Download

Page: 634 / 2320

August 2007

2-442

WorkCentre 5687 Family

11F-130, 11G-130

Status Indicator RAPs

11F-130 Mis-Registration in Stapled and Unstapled Sets
RAP

Use this RAP to identify and correct the causes of mis-registration in stapled sets, resulting in
staples missing some sheets in the set, or poorly registered non-stapled sets.

Procedure

WARNING

Switch off the electricity to the machine, GP 14. Disconnect the power cord. Electricity
can cause death or injury. Moving parts can cause injury.

A probable cause of mis-registration is the condition of the paper and/or damage such as, curl,
wrinkle, creases, dog ears, etc.

•

Curl, wrinkle and creases are probably caused in the IOT, go to the IQ1 Image Quality
Entry RAP.

•

For other copy/print damage and dog ears, go to the 11E-130 Copy Damage in the HCSS
RAP.

Check the following:

•

Check the alignment between the machine and the HCSS, refer to ADJ 11.1-130.

•

Turn over the paper stack in the tray in use.

•

Use a new ream of paper in the tray in use.

•

The paper type especially recycled paper can lead to registration problems. Try changing
to a different brand or type of paper.

•

Ensure that the guides in the paper trays are correctly set and reported on the UI for the
paper size loaded, refer to the 07D Tray 1 and 2 Wrong Size Paper RAP.

•

Check that paper type is set correctly. If heavyweight paper is used but not set in the UI,
the compiler capacity can be exceeded.

•

Check for obstructions in the compiler.

•

Ensure that the compiler belts in the compiler carriage operate correctly and that the belts
are not damaged, PL 11.49 Item 12. Refer to the 11-120-130, 11-122-130 Compiler Car-
riage Jam RAP to check the compiler carriage eject roll motor.

•

Ensure that the paddle roll mechanism in the eject housing of the compiler carriage is
operating correctly, refer to the 11-024-130, 11-025-130 Paddle Position Failure RAP.

•

Ensure that the compiler carriage tampers move to the correct paper size, refer to the fol-
lowing:

–

11-005-130, 11-006-130, 11-310-130, 11-311-130 Compiler Carriage Front Tamper
Move Failure RAP.

–

11-007-130, 11-008-130, 11-312-130, 11-313-130 Compiler Carriage Rear Tamper
Move Failure RAP.

11G-130 HCSS Poor Stacking RAP

Use this RAP to find the cause of poor stacking in the HCSS.

Procedure

Check the following;

•

Look for sets that are not dropping back fully in the bin 1 tray or bin 2 tray and therefore
not being detected by the kicker fingers and sensors:

–

Large paper sizes should not be stacked on top of small paper sizes.

–

Ensure that the paper stack in each paper tray has been fanned.

–

Turn over the paper stack in each paper tray.

–

Ensure that all paper or other copy stock being used is within the size and weight
specifications. Refer to GP 20 Paper and Media Size Specifications.

–

Try using a fresh ream of paper.

–

Ensure that the edge guides of all paper trays are adjusted correctly for the paper
size and that the trays are fully closed.

•

Labels must be fed to bin 0 only.

•

It is recommended that transparencies are fed to bin 0 whenever possible.

•

Check that the machine to HCSS alignment, if necessary perform ADJ 11.1-130 Machine
to HCSS Alignment.

•

Check that the bin 1 upper limit switch, S11-334 and the bin 1 lower limit switch, S11-335
are working correctly. Refer to the 11-030-130, 11-336-130 Bin 1 Movement Failure RAP.

•

Check that the bin 1 offset is working correctly. Refer to 11-031-130, 11-337-130 Bin 1
Offset Failure RAP.

•

Check that the bin 2 upper limit switch, S11-344 and the bin 2 lower limit switch, S11-345
are working correctly. Refer to the 11-036-130, 11-346-130 Bin 2 Movement Failure RAP.

Xerox WorkCentre 5687 Series, Service Manual

Search results

Summary of Contents for WorkCentre 5687 Series

Reviews:

Related manuals for WorkCentre 5687 Series

Brands by name

Popular brands