Xerox WorkCentre Pro 423 Service Manual Download | Manualshive

Page: 16 / 619

background image

WorkCentre 423/428

03/02

INTRODUCTION

6

6 Health and Safety Incident Reporting

6

Health and Safety Incident Reporting

I. Summary

This standard defines requirements for notification of health and safety incidents involving Xerox
products (equipment and materials) at customer locations.

II. Scope

Xerox Corporation and subsidiaries world-wide.

III. Objective

To enable prompt resolution of health and safety incidents involving Xerox products and to ensure
Xerox regulatory compliance.

IV. Definitions

Incident:

An event or condition occurring in a customer account that has resulted in injury, illness or
property damage. Examples of incidents include machine fires, smoke generation, physical injury
to an operator or service representative. Alleged events and product conditions are included in
this definition.

V. Requirements

Initial Report:

1.

Xerox organisations shall establish a process for individuals to report product incidents to
EH&S within 24 hours of becoming aware of the event.

2.

The information to be provided at the time of reporting is contained in Appendix A (Health
and Safety Incident Report involving a Xerox product).

3.

The initial notification may be made by any of the following methods:

•

For incidents in North America and Developing Markets West (Brazil, Mexico, Latin
American North and Latin American South):

•

Phone* EH&S at: 1-800-828-6571.

•

Electronic mail EH&S at: Doris.Bush@usa.xerox.com.

•

Fax EH&S at: 1-716-422-7734 [intelnet 8*222 7734].

•

For incidents in Europe and Developing Markets East (Middle East, Africa, India,
China and Hong Kong):

•

Phone* EH&S at: +44 (0) 1707 35343.

•

Electronic mail EH&S at: Elaine.Grange@GBR.xerox.com.

•

Fax EH&S at: +44 (0) 1707 353914 [intelnet 8*668 3914].

*Initial notification made by phone must be followed within 24 hours by a completed
incident report and sent to the indicated electronic mail address or fax number.

NOTE: If sending a fax, please also send the original via internal mail.

Responsibilities for resolution:

1.

Business Groups/Product Design Teams responsible for the product involved in the incident
shall:

a)

Manage field bulletins, customer correspondence, product recalls, safety retrofits.

b)

Fund all field retrofits.

2.

Field Service Operations shall:

c)

Preserve the Xerox product involved and the scene of the incident inclusive of any

associated equipment located in the vicinity of the incident.

d)

Return any affected equipment/part(s) to the location designated by EH&S and/or the

Business Division.

e)

Implement all safety retrofits.

3. EH&S

shall:

f)

Manage and report all incident investigation activities.

g)

Review and approve proposed product corrective actions and retrofits, if necessary.

h)

Manage all communications and correspondence with government agencies.

i)

Define actions to correct confirmed incidents.

VI. Appendices

The Health and Safety Incident Report involving a Xerox Product (Form # EH&S-700) is available
at the end of this Service Manual.

«
...
14
15
16
17
18
...
»

Summary of Contents for WorkCentre Pro 423












































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WorkCentre Pro 423

Brand: Panasonic Pages: 24

Brand: Oki Pages: 40

Workio DP-1820E

Brand: Panasonic Pages: 38

Brand: EasyThreed Pages: 4

Brand: EASYPRINT Pages: 37

Brand: Oki Pages: 36

Brand: Oki Pages: 3

Brand: Datamax Pages: 95

Mark II E-4205e

Brand: Datamax Pages: 72

Brand: Panasonic Pages: 166

Pixma TS7700i Series

Brand: Canon Pages: 554

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 14

Brand: J&Maya Pages: 21

Brand: Oki Pages: 44

Brand: Zonestar Pages: 25

Brand: Rokit Pages: 16

Brand: Xerox Pages: 2

Brand: Tally Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands