background image

3. CONTROLS 

xi-440.5

1 Level 

front 

2 Front 

highpass 

3  Bypass for front highpass 
4 Front 

lowpass 

5  Bypass for front lowpass   
6 Level 

rear 

7 Rear 

highpass

8  Bypass for rear highpass
9 Rear 

lowpass 

10  Bypass for rear lowpass 
11 Level 

sub

12  Subwoofer lowpass frequency   
13  Subwoofer phase shift 0°-180°
14 Subsonic frequency 
15 Subsonic 

on/off

16 BLC 

connector

17  RCA line inputs front (left and right channels)

18  RCA line inputs rear (left and right channels)
19  RCA subwoofer inputs (left and right channels)

4. CONNECTORS 

1 +12 V and ground power input
2 Remote terminal
3 Fuses (2x40 A)
4 Front speakers connector
5 Rear speakers connector
6 Subwoofer connector

OPTIONAL ACCESSORY

XETEC „ParaQ-7" parametric equalizer for perfect sound

APPLIED TECHNOLOGIES

• HPAA © by 

XETEC

design group GmbH: „High Precision Analog

Amplifier", symmetrical State-of-the-Art power amplifier.

• X-SMPS © by 

XETEC

design group GmbH: „x-Switched-Mode-Power-Supply",

high efficiency power supply

•  VCVS-Filter © by 

XETEC

design group GmbH: „Voltage Controlled

Voltage Source" filters for the crossover networks

•  X-protect © by 

XETEC

design group GmbH: Highly sensitive protection

circuits

2

4

1

17

18

6

7

9

19

11

12

13

3

5

17

18

8

10

19

14

15

16

3

3

1

2

1

3

4

4

6

5

5

Summary of Contents for XIRCUIT Series






Reviews: