iE4 Series User Manual
Rev.1.0
35
3.6 Basic Function
3.6.1 Power On/ Power Off
When the printer is off, press the power button once, and printer will power on.
When the printer is on, press the power button for three seconds. After ringing twice, the printer will
power off.
3.6.2 FEED Button
When the printer is ready, press the feed button, and printer will automatically feed a label under “Label
Mode”. Press the feed button, and the printer will feed the fixed distance under “Continuous Mode”.
When the printer is printing, press the feed button once and it will stop the printing job. Press the feed
button for three seconds and it will cancel the printing job.
When the printer pauses, press the feed button once and it will continue the printing job. Press the feed
button for three seconds and it will cancel the printing job.
When the printer is in dump mode, press the feed button once, then back to the normal printing mode.
When the indicator status flashes slowly(green), press the feed button once and printer will print a label.
3.6.3 Quick Calibration
Users must carry out the calibration under the conditions below:
The first time to use the printer since installation;
The first time to use the printer since sensor cleaning;
Reuse the printer when it has not been used for a long time;
Change a new type of media;
Printer cannot recognize the mark;
Huge change of the operating environment;
Calibration method:
Carry out the calibration manually.
When printer is ready, press the FEED button for 3 seconds until the status indicator(Green) flashes twice. Then
release the button, and printer will start to do the calibration. When printer does the calibration under
Continuous Media Mode, the calibration is invalid.
Carry out the calibration by printer utility tool.
Please refer to detailed information in “Chapter 6 Printer Utility Tool Instructions”.
Note: After the quick calibration, users could open the printer cover to pull back the learned paper in
avoid of paper wasting.
Summary of Contents for iDPRT iE4P
