19
Use
18
Power-Save
Wa
rm
Wa
te
r
T
o
ilet
Seat
POWER-SAVE function saves the cost of electricity by keeping the
warm water and the toilet seat at low temperature.
Adjustment
of
water
pressure
Deodorization
While the water is being sprayed,
Press High or Low button
Initial pressure after the installation is High
If water does not flow due to low water pressure, set to High using the
adjustment button
Press WARM WATER button
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
Warm Water lamp lights up and heating of cleansing water
begins.
Every time the button is pressed, the position of the Warm Water
Temperature Indicator Lamp shifts.
Press SEAT TEMPERATURE button
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
The Seat Temperature Lamp lights up and seat heating
begins.
Every time the button is pressed, the position of the Seat
Temperature Indicator Lamp shifts.
The toilet seat may occasionally wobbles slightly when someone sits on it but it is normal. It is because the
product was designed for one-touch mounting on to the toilet.
The capacity of the Warm Water Tank of the Main Body is about 1.2 liter. It will be drained after about 40
seconds of WARM WATER operation. It will heat up again after 5~7 minutes from the end of operation.
After pressing Power-Save button
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
Seat temperature keep 77
?
?
?
?
?
?W2@6Xhg?
?7<?B1e@@@@@@@@@@e?
?3=?C5e@@@@@@@@@@e?
?V4@0Ye@@he?
@@he?
@@he?
@@he?
@@@@@@@@@?e?
@@@@@@@@@?e?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
?
?
?
?
?
?
during initial 1 hour and lower 68
?
?
?
?
?
?W2@6Xhg?
?7<?B1e@@@@@@@@@@e?
?3=?C5e@@@@@@@@@@e?
?V4@0Ye@@he?
@@he?
@@he?
@@he?
@@@@@@@@@?e?
@@@@@@@@@?e?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
?
?
?
?
?
?
after 1 hour.
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
Water temperature keep 85
?
?
?
?
?
?W2@6Xhg?
?7<?B1e@@@@@@@@@@e?
?3=?C5e@@@@@@@@@@e?
?V4@0Ye@@he?
@@he?
@@he?
@@he?
@@@@@@@@@?e?
@@@@@@@@@?e?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
?
?
?
?
?
?
during initial 1 hour and lower 77
?
?
?
?
?
?W2@6Xhg?
?7<?B1e@@@@@@@@@@e?
?3=?C5e@@@@@@@@@@e?
?V4@0Ye@@he?
@@he?
@@he?
@@he?
@@@@@@@@@?e?
@@@@@@@@@?e?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
@@he?
?
?
?
?
?
?
after 1 hour.
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
Pressing the Power-Save button again will automatically return to the set
temperature.
When you seat during “power-Save” mode
Return to previous setting and Seat warms about 1~2 minutes and
Water warms about 3~5 minutes.
PB-X1000M model returns to the set temperature if press “power-Save”
If the power plug has been pulled out or power failure occurred,
all settings are cancelled. They should be reset.
Press DEODORIZATION button while in operation. (PB-X1500, PB-X2500)
?
?
?
?
?
?
?
?
?
?
?
?W2@6Xh?
?7@@@1h?
?@@@@@h?
?@@@@5h?
?@@@0Yh?
?
?
?
?
?
?
?
?
?
?
?
Deodorization Lamp lights up and deodorization begins.
DEODORIZATION starts immediately when the button is pressed while sitting on the seat.
Pressing the DEODORIZATION button again will stop the
DEODORIZATION after 5 minutes from the start of its operation.
If stand up without pressing “Stop” button, automatically will stop
after 2 minutes.
DEODORIZATION does not stop by pressing the STOP button.
Using the DRY function during DEODORIZATION suspends the
DEODORIZATION while DRY operation lasts.
Water Outlet and Filter
Close the water supply valve
Press the DETACH button and pull the product forward.
Detach the filter section of the water supply valve at the
back of the Bidet and clean the filter using a soft brush to
remove foreign matters. (Accumulation of foreign matters will
cause reduction of sprayed water through the nozzles.)
Exterior
Use soft sponge or cloth and neutral detergent for cleaning.
Detach the toilet seat by pulling the stub for detaching.
Nozzles
If press “forth” button of Nozzle position during 3 seconds, Nozzle will come out.
Gently pull the end of the nozzle forward.
Scrub the end gently using a soft brush.
- Be careful not to damage the holes of the nozzle.
- If press “Stop” buton after cleansing, the nozzle return to the body.
Blocking the nozzle mouth during cleaning may disturb the spray angle.
Be careful not to block or damage the nozzle.
Always unplug the power cord before cleaning.
Storing the Bidet for a prolonged period of suspended use
1. Pull out the plug from the power outlet.
2. Close the water supply valve.
3. Detach the Bidet by pressing the DETACH button on the side.
4. Open the drain cap and drain the water completely.
1. Check if the power plug is firmly in place in the power outlet.
2. Adjust the temperature using the WATER TEMP button.
- Keeping warm of the warm water thank will prevent the
water from freezing.
- If the toilet room is not heated, wrap the connecting pipes
or use another heater.
Prevention of freezing
Summary of Contents for PB-X1000
Page 1: ...4224 0048 00 Rev 00...
Page 12: ......
