background image

Additional safety rules:

 

                   

1. Wear a hard hat (safety helmet), safety glasses and /or face shield. It is also highly recommended 
that you wear a dust mask, ear protectors and thickly padded gloves.

 

2

Be sure the bit is secured in place before operation.

 

3. Under normal operation, the machine is designed to produce vibration, the screws and bolts can come loose, 
causing a breakdown and accidents. Check tightness of them carefully before running.

 

4

In cold weather or a long time tool not be used, please keep the tool running without load a few minutes to 

warm up the grease inside, otherwise hammering function is difficult to get.

 

5

Be sure you stand stably and no one is below when you using tool is in high location.

 

6

Hold the tool firmly with two hands.

 

7

Don't touch any moving parts.

 

8

Don't leave the tool running itself, operate tool only when hand-held.

 

9

Don't point the tool to anybody for the bit could fly out in case.

 

10

When chipping into walls, floors or wherever "live"  electrical wire may be encountered, 

DON'T TOUCH ANY METAL 

PARTS OF THE TOOL! Hold the tool by the insulated grasping 

surface to prevent electric shock if you chip into a "live" wire.

 

11

Don't touch the BIT OR PARTS CLOSE TO THE BIT immediately after operation, they may extremely 

hot and could burn your skin.

 

12

Any damage and abnormal happen, please stop to use immediately and disconnect it, ask authorized serve 

center to check and repair.

 

13. Parts replace:

 Only original XINPU's parts can be used to replace by authorized service center.

 

14. Right use accessories and parts:

 Don't use other parts and accessories which not mentioned in the 

manual otherwise may cause injuries!

 

15. Special attention to voltage:

 Before connect the power tool, please make sure the rated voltage on the 

tool can match the power supply, otherwise the power tool may be damaged and cause injuries.

 

16. Don't wipe plastic part with solvent: 

Solvent such as gasoline, thinner, alcohol etc. these kind of 

chemical material,    are not allowed to use, water or soap are recommended! 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

Summary of Contents for XP-45HS














Reviews: