background image

 

6

 

General Power Tool Safety Warnings 

 

WARNING 

  Read all safety warnings and all instructions   

Failure to 

 

follow all warnings and instructions may 

result in electric shock, fire and/or serious injury.   

 

Save all warnings and instructions for future reference 

The term “power tool” in the warnings refer to your mains operated (corded) power tool or battery operated (cordless) 

power tool. 

 

1) Work 

area 

 

a) Keep work area clean and well lit. 

Cluttered and dark areas invite accidents. 

 

    b)Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases 

or dust. 

Power tools create sparks which may ignite the dust or fumes. 

 

c)  Keep children and bystanders away while operating a power tool. 

Distractions can cause you to lose 

control. 

 

2) Electrical 

safety 

 

a)  Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs 

with earthed (grounded) power tools. 

Unmodified plugs and matching outlets will reduce risk of electric 

shock. 

 

b)  Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. 

There is an increased risk of electric shock if your body is earthed or grounded. 

 

c)  Do not expose power tools to rain or wet conditions. 

Water entering a power tool will increase the risk of 

electric shock. 

 

d)  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord 

away from heat, oil, sharp edges or moving parts. 

Damaged 

or 

entangled 

cords 

increase the risk of electric 

shock. 

 

e)  When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a 

cord 

suitable for outdoor use reduces the risk of

 

electric shock. 

 

f)   

If operating a power tools in a damp location is unavoidable, use a residual current device (RCD) 

protected supply.

 Use of an RCD reduces the risk of electric shock. 

 

3) 

Personal safety

 

 

a)  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a 

power tool while you are tired or under the influence of drugs, alcohol or medication. 

A moment of 

inattention while operating power tools may result in serious personal injury. 

Summary of Contents for XP-G65BC-1

















Reviews: