Xirgo Technologies XT4970D User Manual Download | Manualshive

Page: 8 / 14

background image

8

3 Device Mounting Options

3.1 Screw Mounting

The XT4970D has two flanges (two holes per) at each end of the housing for screw mounting the

device to the mounting surface.

3.2 3M VHB Tape Mounting

For a semi-permanent option, the device can be mounted with 3M VHB tape as shown below:

«
...
6
7
8
9
10
...
»

Summary of Contents for XT4970D















Reviews:

No comments

Related manuals for XT4970D

Brand: Navitel Pages: 32

Brand: Davtron Pages: 2

010-11018-00 - Mobile PC - GPS Software

Brand: Garmin Pages: 1

RUNNING DYNAMICS POD

Brand: Garmin Pages: 128

Brand: Communica Pages: 21

Brand: TopflyTech Pages: 16

TRAFFIC ASSIT 7928

Brand: Becker Pages: 108

Brand: Rope Pages: 12

BMW Motorrad Navigator IV

Brand: Garmin Pages: 48

Brand: Tramigo Pages: 2

Brand: Tramigo Pages: 2

W3G - W3G LCD Color Touch Screen Portable GPS/MP3

Brand: Nextar Pages: 22

Brand: Nextar Pages: 13

Brand: RedPort Pages: 4

Brand: OzSpy Pages: 8

Brand: MobileHelp Pages: 12

Brand: OwnFone Pages: 2

Brand: RoyalTek Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands