background image

 

 

              

14 

FCC/IC: 

REGULATORY COMPLIANCE INFORMATION 

 

This equipment with FCC-ID: GKM-XT4971A and IC-ID: 10281A-XT4971A, HVIN: XT4971A

 

 
is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. 
 

Changes or modifications not expressly approved by the party responsible for compliance could void the user's 
authority to operate the equipment. 
 

This device complies with Part 15 of the FCC Rules and with license exempt Radio Standard Specifications of 
Industry Canada. 
Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that may cause undesired 
operation. 
 

Les changements ou modifications non expressément approuvés par la partie responsable de la conformité 
pourraient annuler l'autorité de l'utilisateur à utiliser l'équipement. 
 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de 
licence. L'exploitation est autorisée aux deux conditions suivantes : 
(1) l'appareil ne doit pas produire de brouillage, et 

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d'en compromettre le onctionnemen 
 

 
Radio frequency radiation exposure Information: 
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with minimum distance of 20 cm 

between the radiator and your body. Co-location of this radio device with other radio transmitters may void it's 
compliance with the said RF exposure limits and would have to be subject to re-assessment.

 

 

Summary of Contents for XT4971A Series















Reviews: