background image

 

 

              

13 

4.2 Configuring the Device via SMS 

 

1)

 

Ensure your device is active on your cellular account.

 

2)

 

Awaken device from sleep XT4975A 

via the “wake

-

up” button

 

3)

 

If the device needs more power, then supply 12V DC via the red wire of the cable harness.

 

4)

 

Ensure device cellular LED is blinking based on LED definition in this document.

 

5)

 

Using your mobile phone or SMS gateway send +XT:1008 command to the device MDN

 

6)

 

Command: “+XT:1008,<SM>”

- Sets SMS Number

 

7)

 

Response (via SMS): $$<UID>,<1008>,<SM>##

 

8)

 

Once you have set SMS to reply to your mobile or gateway, you can now send other 

commands to device via SMS per device protocol documentation. 

 

a.

 

CXT:1010 configures network settings

 

b.

 

CXT:3017 configures the sleep/wake mode for the device. 

 

i.

 

The factory defaults for this device is to operate in the sleep timer mode and 

have a minute of wake time max. You may need to temporarily disable sleep 
in order to configure the unit uninterrupted by sleep.

 

c.

 

CXT:3040 and +XT:3042 configure alert and threshold settings

 

9)

 

+XT:7008,<PF> saves device configuration to permanent memory. You may configure 

individual features and the 7008 command will save all the configuration state at that 
instance.

 

4.3 Configuring the Device via PC 

 

1)

 

A RS-232 to USB TTL converter cable is required to connect the XT4975A to a computer 

for local configuration.   Connect the XT4975A Tx wire to the TTL converter cable Rx wire.  

Connect the XT4975A Rx wire to the TTL converter cable Tx wire.  Connect the XT4975A 
ground wire to the ground wire of the TTL converter cable.  Use a terminal application to 
connect to the COM port associated with the TTL converter cable.  

 

2)

 

Use the following terminal application settings: 

a.

 

Bits per second: 115200 

b.

 

Data bits: 8 

c.

 

Parity: None 

d.

 

Stop bits: 1 

e.

 

Flow control: None 

3)

 

Press enter 3 times to activat

e the Aux Port. The print “Aux Port Active” will show up on 

your terminal console when activated successfully. 

4)

 

Once Aux Port is active login to the device using the AES challenge prompt. Please contact 

your Xirgo FAE to get instructions on how to complete this process. 

5)

 

The terminal console will print 

Accepted

 when successfully completed challenge prompt.

 

 

 

 

 
 

Summary of Contents for XT4975A Series

















Reviews: