Xirgo XT4975A Series User Manual Download | Manualshive

Page: 8 / 16

background image

8

3 Device Mounting Options

3.1 Screw Mounting

The XT4975A has two flanges (two holes per) at each end of the housing for screw mounting the
device to the mounting surface.

3.2 3M VHB Tape Mounting

For a semi-permanent option, the device can be mounted with 3M VHB tape as shown below:

«
...
6
7
8
9
10
...
»

Summary of Contents for XT4975A Series

















Reviews:

No comments

Related manuals for XT4975A Series

RoadMate Series

Brand: Magellan Pages: 14

RoadMate 1440 - Automotive GPS Receiver

Brand: Magellan Pages: 19

RoadMate 1200 - Automotive GPS Receiver

Brand: Magellan Pages: 31

RoadMate 1200 - Automotive GPS Receiver

Brand: Magellan Pages: 33

RoadMate 1200 - Automotive GPS Receiver

Brand: Magellan Pages: 8

Brand: Sensitech Pages: 2

Brand: T-Mark Pages: 14

Brand: Garmin Pages: 4

Brand: JRC Pages: 2

Brand: Teltonika Pages: 16

Brand: Navilock Pages: 36

GHP 20 Marine Autopilot System for...

Brand: Garmin Pages: 36

Brand: Gator Pages: 24

Brand: Advanced Telemetry Systems Pages: 73

Brand: Dual Pages: 13

Brand: Micron Electronics Pages: 9

Brand: Xirgo Pages: 14

Brand: XITONG Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands