background image

When a cell phone that has been paired and is currently connected with the 
XLink rings, all telephones plugged into the XLink will also ring.

Each line has its own distinctive ring pattern, allowing you to immediately know 
which cell phone the current call is coming in on.

SeleCTInG lIne

reCeIvInG a Call

After.picking.up.a.telephone.connected.to.the.XLink,.you.should.hear.a.steady.dial.
tone,.if.you.hear.an.error.tone.(series.of.rapid.beeps),.there.are.no.lines.available.for.an.
outgoing.call..In.this.case,.check.to.ensure.that.you.have.at.least.one.cell.phone.paired.
and.connected.to.the.XLink.

The XLInk uses the lowest line number with a connected cell phone for outgoing 
calls. For example, if cell phones for lines 2 and 3 are connected, all outgoing 
calls will be made on line 2.
A specific line can be specified on a per call basis by first dialing the desired line 
number and then pressing the  FLAsh  key on your telephone.
Example: To specify line 3 for an outgoing call, dial  3  FLAsh , then dial the 
intended phone number. 
Anytime a rapid series of beeps is heard instead of normal dial tone, that  
specific line (or any line) is not available for outgoing calls. This is because the 
XLink has not been paired with a cell phone or the cell phone is out of range.

Summary of Contents for ITC-BT

























Reviews: