3
ENGLISH
SIGNAL : STRONG
SIGNAL : MARGINAL
Signal strength is good
Signal strength is marginal
SIGNAL : WEAK
SIGNAL : NON
Signal strength is poor
Loss of the signal
2.
Adjust the antenna location until Signal
strength is good.
3.
Turn the
GYRO TUNING
dial or tap the channel
or
button on the remote control unit to
select channel 0 (XM000).
• The Radio ID is displayed.
Note:
• If “
CHECK ANTENNA
” appears in the front
panel display, the XM Connect-and-Play antenna
may not be connected to the XM terminal on the
rear panel of this unit properly.
LISTENING TO XM SATELLITE RADIO
SELECTING AN INPUT SOURCE
Before you can listen to XM Satellite Radio, you
must first select the input source on the SR9600.
MULTI
SPEAKER
F/P
BAND
THX
THX
PURE DIRECT
PURE DIRECT
UP
DOWN
TUNING
AUX 1 INPUT
R
AUDIO
DIGITAL
S-VIDEO
L
VIDEO
POWER ON/STANDBY
POWER ON/STANDBY
VOLUME
UP
DOWN
INPUT SELECTOR
INPUT SELECTOR
PHONES
PHONES
STANDBY
STANDBY
AV SURROUND RECEIVER SR9600
AV SURROUND RECEIVER SR9600
SURROUND
SURROUND
MIC
ENTER
MENU
PURE DIRECT
PURE DIRECT
THX
THX
7.1
7.1CH INPUT
MODE
MODE
AUTO
AUTO
MULTI
MULTI
A/B
T-MODE
MEMORY
CLEAR
DISPLAY
EXIT
SPEAKERS
MRAC
AUTO TUNE
1.
1.
Select “
XM
” by turning the
INPUT SELECTOR
knob on the front panel.
Or, tap the “
XM
” on the remote control unit.
CHECKING THE XM SIGNAL STRENGTH AND
RADIO ID
1.
Tap the
Disp.
twice on the remote control
unit. Signal status is displayed.
• The display changes as shown below
according to the receiving condition.
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
You can display XM information (such as artist
name, song title, category or signal status) for the
channel currently selected in the front panel
display.
1.
Tap the
Disp.
button on the remote control
unit repeatedly to toggle between the
following channel information display modes.
Artist name/Song title
Channel category
Signal Status
Surround mode (OSD ON)
When the channel Artist name/Song title is
displayed:
When the channel category is displayed:
When the signal status is displayed:
Radio ID
DIGITAL
1/8
A/V Amp
Source Select
wed Jun 01
4:40
pm
1.
1/2
XM
XM : Main
wed Jun 01
4:40
pm
1.
1/2
XM
XM : Main
wed Jun 01
4:40
pm
1.
When the Surround mode is displayed:
The video monitor output will show OSD information.
Note:
• The front panel display can indicate up to 20
alphanumeric characters at once. If the information
contains more than 20 characters, the information
scrolls from right to left.
• If the information contains a character that cannot
be recognized by that unit, the character will be
displayed with “ ” (space).
X M
I N F O R M A T I O N
X
C
N
T
C
S
M
H
A
I
A
I
A
M
T
T
G
N
E
L
N
E
A L
:
:
:
:
:
:
0
D
P
M
R
S
4
e
i
o
o
T
0
e
n
n
c
R
p
k
e y
k
O
T
N
r
F
G
a
l
c
o
k
i
s
d
SR9600U DFU̲01̲ENG XM
06.1.16, 4:44 PM
Page 3
Adobe PageMaker 6.5J/PPC
