background image

NOTE:  Hand tighten bolts and nylon nuts until machine is fully 
assembled.

SAFETY PRECAUTIONS

SAFETY INFORMATION WARNING!

Prior to assembly, remove components from the box and verify that all the listed parts 
were supplied.  

 Before using this unit or starting any exercise program, consult your physician.  
This is especially important for persons over the age of 35 and/or persons with pre-
existing health problems.  XMARK Fitness assumes no responsibility for personal
injury or property damage sustained by or through the use of this product.

It is the owner’s responsibility to ensure that all users of this unit have read the 
Owner’s Manual and are familiar with safety information and precautions.

 This unit should only be used on a level surface and is intended for indoor use
only. XMARK Fitness recommends an equipment mat be placed under the unit to
protect the floor or carpet and for easier cleaning.

 Wear comfortable, good-quality walking or running shoes and appropriate cloth-
ing. Do not use this unit with bare feet, sandals, socks or stockings!

 Always examine your unit before using to ensure all parts are in working order.

 Do not leave children unsupervised near or on the unit.

 Service to your unit should only be performed by an authorized service represen-
tative, unless authorized and/or instructed by a XMARK

  Fitness technician. Failure

to follow these instructions will void the warranty.

Important Safety Information

3

Summary of Contents for XM-7617














Reviews: